The reset command should be the first command sent to the SLC NAND.
Resetting the SLC NAND should not be done only if NAND_ONFI_DETECT
is enabled.
Change-Id: If225a1b1a7e04181cc5839e282c435c5c8958bd7
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
The framework currently supports QE feature only for Macronix devices.
Kioxia devices also support this feature, but this feature can not be
set based on the manufacturer ID as Kioxia first SPI NAND generation
does not support the QE feature when the second generation does.
Use a flag to manage QE feature. This flag will be added at board level
to manage the device.
Change-Id: I7a3683a2df8739967b17b4abbec32c51bf206b93
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
The scratch buffer could be large. The new function allows
platform to defined its own external buffer or use the default
one.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Change-Id: Ib7ab8ff19fa0a9cb06e364f058b91af58c3c471a
Some messages don't use the correct types, update them.
This avoids warning when -Wformat-signedness is enabled.
Change-Id: Ie5384a7d139c48a623e1617c93d15fecc8a36061
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Add the SZ_* macros from 32 to 2G.
This allows removing some defines in raw NAND driver
and STM32MP1 boot device selection code.
Change-Id: I3c4d4959b0f43e785eeb37a43d03b2906b7fcfbc
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
On most of SPI NAND, the read id command needs a dummy byte,
except GIGADEVICE SPI NAND that needs an address.
To be compliant with all memories providers, the first byte returns
by the READ_ID command is not relevant (garbage).
Change-Id: Ife74ccab333dd1a04799abe230d3f07fa6ea1edb
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
This patch checks that the SPI NAND parameters needed by
the framework have been set before starting to read data.
Change-Id: I17b36606701c44864dcf1783f810da5c8cbf88f2
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
In case of FIP, the offsets given in the FIP header are relative.
If bad blocks are found between the FIP base address and this offset,
the offset should be updated, taking care of the bad blocks.
Change-Id: I96fefabb583b3d030ab05191bae7d45cfeefe341
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
nand_wait_ready is called with a millisecond delay
but the timeout used a micro second. Fixing the conversion
in the timeout call.
The prototype of the function is also changed to use an unsigned int
parameter.
Change-Id: Ia3281be7980477dfbfdb842308d35ecd8b926fb8
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This framework supports SPI-NAND and is based on the
SPI-MEM framework for SPI operations. It uses a common high
level access using the io_mtd.
It is limited to the read functionalities.
Default behavior is the basic one data line operation
but it could be overridden by platform.
Change-Id: Icb4e0887c4003a826f47c876479dd004a323a32b
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
The raw NAND framework supports SLC NAND devices.
It introduces a new high level interface (io_mtd) that
defines operations a driver can register to the NAND framework.
This interface will fill in the io_mtd device specification:
- device_size
- erase_size
that could be used by the io_storage interface.
NAND core source file integrates the standard read loop that
performs NAND device read operations using a skip bad block strategy.
A platform buffer must be defined in case of unaligned
data. This buffer must fit to the maximum device page size
defined by PLATFORM_MTD_MAX_PAGE_SIZE.
The raw_nand.c source file embeds the specific NAND operations
to read data.
The read command is a raw page read without any ECC correction.
This can be overridden by a low level driver.
No generic support for write or erase command or software
ECC correction.
NAND ONFI detection is available and can be enabled using
NAND_ONFI_DETECT=1.
For non-ONFI NAND management, platform can define required
information.
Change-Id: Id80e9864456cf47f02b74938cf25d99261da8e82
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Christophe Kerello
Lionel Debieve
Yann Gautier
Yann Gautier
Lionel Debieve