Currently the Run-time UART is mapped to AP UART1 which is internally
routed to MCP UART1, so unsharing it from AP UART1 and mapping it to
IOFPGA UART0 for exclusiveness among the usage of the UARTs.
Signed-off-by: Himanshu Sharma <Himanshu.Sharma@arm.com>
Change-Id: I366740a971a880decf0d373e9055e7ebda5df53a
These changes are to add support for loading and booting
OP-TEE as SPMC running at SEL1 for N1SDP platform.
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Change-Id: I0514db646d4868b6f0c56f1ea60495cb3f7364fd
This patch adds support to load nt_fw_config with the information from
plat_info sds structure which is then passed from BL2 to BL33.
Signed-off-by: sahil <sahil@arm.com>
Change-Id: I2fcf13b7bf5ab042ef830157fd9cceedbdca617a
Enable basic support for Neoverse-N2 CPUs.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I498adc2d9fc61ac6e1af8ece131039410872e8ad
Allocated 512-959 SPI numbers for remote n1sdp chip and same has been
referenced for GIC routing table.
Change-Id: Id79ea493fd665ed93fe9644a59e363ec10441098
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>
The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.
This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.
Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch moves all GICv3 driver files into new added
'gicv3.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
The patch adds GICv3 driver configuration flags
'GICV3_IMPL', 'GICV3_IMPL_GIC600_MULTICHIP' and
'GICV3_OVERRIDE_DISTIF_PWR_OPS' described in
'GICv3 driver options' section of 'build-option.rst'
document.
NOTE: Platforms with GICv3 driver need to be modified to
include 'drivers/arm/gic/v3/gicv3.mk' in their makefiles.
Change-Id: If055f6770ff20f5dee5a3c99ae7ced7cdcac5c44
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Since N1SDP has a system level cache which is an
external LLC enable the NEOVERSE_N1_EXTERNAL_LLC flag.
Change-Id: Idb34274e61e7fd9db5485862a0caa497f3e290c7
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.
Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.
Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.
Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
N1SDP supports multichip configuration wherein n1sdp boards are
connected over high speed coherent CCIX link, for now only dual-chip
is supported.
Whether or not multiple chips are present is dynamically probed by
SCP firmware and passed on to TF-A, routing table will be set up
only if multiple chips are present.
Initialize GIC-600 multichip operation by overriding the default GICR
frames with array of GICR frames and setting the chip 0 as routing
table owner.
Change-Id: Ida35672be4bbf4c517469a5b330548d75e593ff2
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
N1SDP supports multichip configuration wherein n1sdp boards are
connected over high speed coherent CCIX link for now only dual-chip is
supported.
A single instance of TF-A runs on master chip which should be aware of
slave chip's CPU and memory topology.
This patch updates platform macros to include remote chip's information
and also ensures that a single version of firmware works for both single
and dual-chip setup.
Change-Id: I75799fd46dc10527aa99585226099d836c21da70
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Platform information structure holds information about platform's DDR
size(local/remote) which will be used to zero out the memory before
enabling the ECC capability as well as information about multichip
setup. Multichip and remote DDR information can only be probed in SCP,
SDS region will be used by TF-A to get this information at boot up.
This patch introduces a new SDS to store platform information, which is
populated dynamically by SCP Firmware.previously used mem_info SDS is
also made part of this structure itself.
The platform information is also passed to BL33 by copying it to Non-
Secure SRAM.
Change-Id: I4781dc6a7232c3c0a3219b164d943ce9e3e469ee
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
NOTE: AARCH32/AARCH64 macros are now deprecated in favor of __aarch64__.
All common C compilers pre-define the same macros to signal which
architecture the code is being compiled for: __arm__ for AArch32 (or
earlier versions) and __aarch64__ for AArch64. There's no need for TF-A
to define its own custom macros for this. In order to unify code with
the export headers (which use __aarch64__ to avoid another dependency),
let's deprecate the AARCH32 and AARCH64 macros and switch the code base
over to the pre-defined standard macro. (Since it is somewhat
unintuitive that __arm__ only means AArch32, let's standardize on only
using __aarch64__.)
Change-Id: Ic77de4b052297d77f38fc95f95f65a8ee70cf200
Signed-off-by: Julius Werner <jwerner@chromium.org>
The DMC-620 memory controllers in N1SDP platform has to be put
into CONFIG state before writing to ERR0CTLR0 register to enable
ECC.
This patch fixes the sequence so that DMCs are set to CONFIG
state before writing to ERR0CTLR0 register and moved back to
READY state after writing.
Change-Id: I1252f3ae0991603bb29234029cddb5fbf869c1b2
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.
Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.
Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
The default DRAM2 start address for Arm platforms
is 0x880000000. However, for N1SDP platform this is
0x8080000000.
Fix the DRAM2 start address by initialising
PLAT_ARM_DRAM2_BASE.
Without this fix there is a mismatch of the System
memory region view as seen by the BL31 runtime
firmware (PSCI) versus the view of the OS (which
is based on the description provided by UEFI. In
this case UEFI is correctly describing the DRAM2
start address).
This implicates in secondary cores failing to start
on some Operating Systems if the OS decides to place
the secondary start address in the mismatched region.
Change-Id: I57220e753219353dda429868b4c5e1a69944cc64
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.
So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.
Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
MHU doorbell driver requires arm platform specific
macro "PLAT_CSS_MHU_BASE".
Rename it to "PLAT_MHUV2_BASE", so that platforms other than arm
can use generic MHU doorbell driver.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
The variable is renamed to PLAT_ARM_RUN_UART as
the UART is used outside BL31 as well.
Change-Id: I00e3639dfb2001758b7d24548c11236c6335f64a
Signed-off-by: Usama Arif <usama.arif@arm.com>
Use full include paths like it is done for common includes.
This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.
Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.
This also prevents problems like cyclic dependencies.
Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch removes the dependency of the N1SDP on soc
css defines in order to let the N1SDP platform port
define the uart related constants.
Change-Id: If13796f278586a01512ee99615502b30e478189e
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
In order to allow Arm platforms to override the default list of PSCI
callbacks, remove the existing weak implementation of
'plat_arm_psci_override_pm_ops' function and let all the Arm platforms
implement their own 'plat_arm_psci_override_pm_ops' function.
For platforms that support SCMI protocol, the function
'css_scmi_override_pm_ops' can be additionally used as well to
override the default PSCI callbacks.
Change-Id: If7c27468bd51a00ea9c2a3716b5894163f5a9f3c
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
The CSS_SYSTEM_PWR_DMN_LVL macro that defines the system power domain
level is fixed at ARM_PWR_LVL2 for all CSS platforms. However, the
system power domain level can be different for CSS platforms that
use multi-threaded CPUs.
So, in preparation towards adding support for platforms that use
multi-threaded CPUs, refactor the definition of CSS_SYSTEM_PWR_DMN_LVL
such that CSS_SYSTEM_PWR_DMN_LVL is uniquely defined for each of the
CSS platform.
Change-Id: Ia837b13f6865e71da01780993c048b45b7f36d85
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.
The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.
The exceptions are files that are imported from other projects:
- CryptoCell driver
- dt-bindings folders
- zlib headers
Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds support for the N1SDP (NeoVerse N1 System Development
Platform). It is an initial port and additional features are expected
to be added later.
The port includes only BL31 support as the System Control Processor
(SCP) is expected to take the role of primary boatloader
Change-Id: Ife17d8215a7bfcc1420204a72205e7ef920d0c10
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>
Himanshu Sharma
Vishnu Banavath
sahil
Javier Almansa Sobrino
Sayanta Pattanayak
Andre Przywara
Alexei Fedorov
Chandni Cherukuri
Aditya Angadi
Max Shvetsov
Manish Pandey
Julius Werner
Manoj Kumar
Sami Mujawar
Masahisa Kojima
John Tsichritzis
Usama Arif
Antonio Nino Diaz
Deepak Pandey