The value of the macro CSS_SGI_REMOTE_CHIP_MEM_OFFSET can be different
across all the Neoverse reference design platforms. This value depends
on the number of address bits used per chip. So let all platforms define
CSS_SGI_ADDR_BITS_PER_CHIP which specifies the number of address bits
used per chip.
In addition to this, reuse the definition of CSS_SGI_ADDR_BITS_PER_CHIP
for single chip platforms and CSS_SGI_REMOTE_CHIP_MEM_OFFSET for multi-
chip platforms to determine the maximum address space size. Also,
increase the RD-N2 multi-chip address space per chip from 4TB to 64TB.
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Change-Id: If5e69ec26c2389304c71911729d4addbdf8b2686
A Neoverse reference design platform can have two or more variants that
differ in core count, cluster count or other peripherals. To allow reuse
of platform code across all the variants of a platform, introduce build
option CSS_SGI_PLATFORM_VARIANT for Arm Neoverse reference design
platforms. The range of allowed values for the build option is platform
specific. The recommended range is an interval of non negative integers.
An example usage of the build option is
make PLAT=rdn2 CSS_SGI_PLATFORM_VARIANT=1
Change-Id: Iaae79c0b4d0dc700521bf6e9b4979339eafe0359
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Define a default DMC-620 TZC memory region configuration and use it to
specify the TZC memory regions on sgi575, rdn1edge and rde1edge
platforms. The default DMC-620 TZC memory regions are defined
considering the support for secure paritition as well.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: Iedee3e57d0d3de5b65321444da51ec990d3702db
The macros specific to SDEI defined in the sgi_base_platform_def.h are
not applicable for all the platforms supported by plat/sgi. So refactor
the SDEI specific macros into a new header file and include this file on
only on platforms it is applicable on.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I0cb7125334f02a21cae1837cdfd765c16ab50bf5
Upcoming RD platforms have deviations in various definitions of
platform macros from that of the exisiting platforms. In preparation
for adding support for those upcoming RD platforms, refactor the
header file inclusion to allow newer platforms to use a different
set of platform macros.
Change-Id: Ic80283ddadafaa7f766f300652cb0d4e507efdb6
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Upcoming RD platforms have a different memory map from those of the
existing platforms. So make the build of the existing mmap entries to be
usable only for existing platforms and let upcoming platforms define
a different set of mmap entries.
Change-Id: Id1ef0293efe8749c78a99237e78d32573c7233aa
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
This patch adds dependencies to the generated configuration
files that are included in the FIP. This fixes occasional
build errors that occur when the FIP happens to be built first.
Change-Id: I5a2bf724ba3aee13954403b141f2f19b4fd51d1b
Signed-off-by: Anders Dellien <anders.dellien@arm.com>
This resolves MISRA defects such as:
plat/common/plat_bl1_common.c:63:[MISRA C-2012 Rule 14.4 (required)]
The condition expression "1" does not have an essentially boolean type.
Change-Id: I679411980ad661191fbc834a44a5eca5494fd0e2
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Moved BL2 configuration nodes from fw_config to newly
created tb_fw_config device tree.
fw_config device tree's main usage is to hold properties shared
across all BLx images.
An example is the "dtb-registry" node, which contains the
information about the other device tree configurations
(load-address, size).
Also, Updated load-address of tb_fw_config which is now located
after fw_config in SRAM.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ic398c86a4d822dacd55b5e25fd41d4fe3888d79a
As per "include/export/README", TF-A code should never include export
headers directly. Instead, it should include a wrapper header that
ensures the export header is included in the right manner.
"tbbr_img_def_exp.h" is directly included in TF-A code, this patch
replaces it with its wrapper header "tbbr_img_def.h".
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I31c1a42e6a7bcac4c396bb17e8548567ecd8147d
Dynamic configuration properties are fconf properties. Modify the
compatible string from "arm,.." to "fconf,.." to reflect this.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: I85eb75cf877c5f4d3feea3936d4c348ca843bc6c
The cookie will be leveraged in the next commit.
Change-Id: Ie8bad275d856d84c27466461cf815529dd860446
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
In preparation for adding support for Reference Design platforms
which have different base addresses for GIC Distributor or
Redistributor, move GIC related base addresses to individual platform
definition files.
Change-Id: Iecf52b4392a30b86905e1cd047c0ff87d59d0191
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Introduce macro 'CSS_SGI_CHIP_COUNT' to allow Arm CSS platforms with
multi-chip support to define number of chiplets on the platform. By
default, this flag is set to 1 and does not affect the existing single
chip platforms.
For multi-chip platforms, override the default value of
CSS_SGI_CHIP_COUNT with the number of chiplets supported on the
platform. As an example, the command below sets the number of chiplets
to two on the RD-N1-Edge multi-chip platform:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all
Change-Id: If364dc36bd34b30cc356f74b3e97633933e6c8ee
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Include multi-chip-mode parameter in HW_CONFIG dts to let next stage of
boot firmware know about the multi-chip operation mode.
Change-Id: Ic7535c2280fd57180ad14aa0ae277cf0c4d1337b
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.
Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Multi-chip platforms have two or more identical chips connected using a
high speed coherent link. In order to identify such platforms,
add chip_id and multi_chip_mode information in the platform variant
info structure. The values of these two new elements is populated
during boot.
Change-Id: Ie6e89cb33b3f0f408814f6239cd06647053e23ed
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
For SGI-575 and RD platforms, move bl31_platform_setup handler to
individual board files to allow the platforms to perform board specific
bl31 setup.
Change-Id: Ia44bccc0a7f40a155b33909bcb438a0909b20d42
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Enables usage of ARM_ROTPK_LOCATION=regs for FVP board.
Removes hard-coded developer keys. Instead, setting
ARM_ROTPK_LOCATION=devel_* takes keys from default directory.
In case of ROT_KEY specified - generates a new hash and replaces the
original.
Note: Juno board was tested by original feature author and was not tested
for this patch since we don't have access to the private key. Juno
implementation was moved to board-specific file without changing
functionality. It is not known whether byte-swapping is still needed
for this platform.
Change-Id: I0fdbaca0415cdcd78f3a388551c2e478c01ed986
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
The platform topology description of the upcoming Arm's RD platforms
have different topology than those listed in the sgi_topology.c file. So
instead of adding platform specific topology into existing
sgi_topology.c file, those can be added to respective board files. In
order to maintain consistency with the upcoming platforms, move the
existing platform topology description to respective board files.
Change-Id: I4689c7d24cd0c75a3dc234370c34a85c08598abb
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
NOTE for platform integrators:
API `plat_psci_stat_get_residency()` third argument
`last_cpu_idx` is changed from "signed int" to the
"unsigned int" type.
Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.
2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent
Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.
Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c
NOTE: AARCH32/AARCH64 macros are now deprecated in favor of __aarch64__.
All common C compilers pre-define the same macros to signal which
architecture the code is being compiled for: __arm__ for AArch32 (or
earlier versions) and __aarch64__ for AArch64. There's no need for TF-A
to define its own custom macros for this. In order to unify code with
the export headers (which use __aarch64__ to avoid another dependency),
let's deprecate the AARCH32 and AARCH64 macros and switch the code base
over to the pre-defined standard macro. (Since it is somewhat
unintuitive that __arm__ only means AArch32, let's standardize on only
using __aarch64__.)
Change-Id: Ic77de4b052297d77f38fc95f95f65a8ee70cf200
Signed-off-by: Julius Werner <jwerner@chromium.org>
The watchdog is configured with a default value of 256 seconds in order
to implement the Trusted Board Boot Requirements.
For the FVP and Juno platforms, the FWU process relies on a watchdog
reset. In order to automate the test of FWU, the length of this process
needs to be as short as possible. Instead of waiting for those 4 minutes
to have a reset by the watchdog, tell it to reset immediately.
There are no side effects as the value of the watchdog's load register
resets to 0xFFFFFFFF.
Tested on Juno.
Change-Id: Ib1aea80ceddc18ff1e0813a5b98dd141ba8a3ff2
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.
Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.
Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
Improved support for W=1 compilation flag by solving missing-prototypes
and old-style-definition warnings.
The libraries are compiling with warnings (which turn into errors with
the Werror flag).
Outside of libraries, some warnings cannot be fixed without heavy
structural changes.
Change-Id: I1668cf99123ac4195c2a6a1d48945f7a64c67f16
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
MHU doorbell driver requires arm platform specific
macro "PLAT_CSS_MHU_BASE".
Rename it to "PLAT_MHUV2_BASE", so that platforms other than arm
can use generic MHU doorbell driver.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
With the two new APIs 'plat_arm_sgi_get_platform_id' and
'plat_arm_sgi_get_config_id' that are available now, BL31 need not
depend on hw_config device tree to identify the platform. In addition
to this, the existing hardware description in hw_config can be limited
to use by BL33 and not by the operating system.
So the hardware description from hw_config dts can be moved into
nt_fw_config dts and the use of hw_config dts can be removed.
Change-Id: I873b7e1e72823d3ec5d253a848e85ae724f09e49
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Add two new functions 'plat_arm_sgi_get_platform_id' and
'plat_arm_sgi_get_config_id' which will be implemented by all the
SGI platforms. These functions can be used to determine the part
number and configuration id of the SGI platforms.
In BL2, these functions are used to populate the 'system-id' node.
In BL31, these functions are used to populate the 'sgi_plat_info_t'
structure with the part number and configuration id of the platform.
Change-Id: I3bacda933527724a3b4074ad4ed5b53a81ea4689
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
For platforms with multi-threaded CPUs, the number of power domains
supported would be more than the value currently defined by
PLAT_MAX_PWR_LVL. So move the PLAT_MAX_PWR_LVL macro to platform
specific code and let the platform define the number of power domain
levels.
Change-Id: I21c0682e62b397860b2999031a0c9c5ce0d28eed
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
The CSS_SYSTEM_PWR_DMN_LVL macro that defines the system power domain
level is fixed at ARM_PWR_LVL2 for all CSS platforms. However, the
system power domain level can be different for CSS platforms that
use multi-threaded CPUs.
So, in preparation towards adding support for platforms that use
multi-threaded CPUs, refactor the definition of CSS_SYSTEM_PWR_DMN_LVL
such that CSS_SYSTEM_PWR_DMN_LVL is uniquely defined for each of the
CSS platform.
Change-Id: Ia837b13f6865e71da01780993c048b45b7f36d85
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Remove the platform common plat_arm_security_setup function to allow
platform specific implementations of the security setup function
implemented in the board directory of the platform.
For use by secure software, configure region0 of DMC-620 trustzone
controller to protect the upper 16MB of memory of the first DRAM block
from non-secure accesses.
Change-Id: I9a8c19656702c4fa4f6917b3655b692d443bb568
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Dynamically populating the 'system-id' node in the HW_CONFIG dts makes
it difficult to enforce memory overlap checks. So add the system-id node
in the HW_CONFIG dts file as a place holder with 'platform-id' and
'config-id' set to zero.
The code at BL2 stage determines the values of 'platform-id' and
'config-id' at runtime and updates the corresponding fields in the
system-id node of HW_CONFIG dts.
Change-Id: I2ca9980b994ac418da8afa0c72716ede10aff68a
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
To align the placement of ftds files with that of other Arm platforms,
move the ftds files from plat/arm/css/sgi/ to plat/arm/board/sgi575.
Change-Id: Id7c772eb5cf3d308d4e02a3c8099218e889a0e96
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
In preparation of adding support for upcoming SGI platforms, macros
common to all the SGI platforms are moved into sgi_base_platform_def.h
file. Macros that are specific to sgi575 platform remain in the
platform_def.h file. In addition to this, the platform_def.h file is
moved to sgi575 board directory. Also the ENT_CPU_SOURCES has been
renamed to SGI_CPU_SOURCES and moved from sgi-common.mk to board
specific makefile platform.mk
Change-Id: Iccdd9f070f4feea232b9fbf4fdcc0ef2e8eccbf2
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
This way it can be reused by other platforms if needed.
Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.
Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.
Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
All the arm platforms were including the files related to
mem-protect. This configuration generates some problems
with new platforms that don't support such functionality,
and for that reason this patch moves these files to the
platform specific makefiles.
Change-Id: I6923e5224668b76667795d8e11723cede7979b1e
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Add support for System Guidance for Infrastructure platform SGI575.
Change-Id: I0125c2ed4469fbc8367dafcc8adce770b6b3147d
Signed-off-by: Nariman Poushin <nariman.poushin@linaro.org>
Vijayenthiran Subramaniam
Aditya Angadi
Thomas Abraham
Anders Dellien
Jimmy Brisson
Manish V Badarkhe
Manish Pandey
Louis Mayencourt
Sandrine Bailleux
Max Shvetsov
Deepika Bhavnani
Julius Werner
Ambroise Vincent
Manoj Kumar
Masahisa Kojima
Antonio Nino Diaz
Chandni Cherukuri
Roberto Vargas
Nariman Poushin