Since non-TF ROM is used in HiKey platform (Hisilicon Hi6220 SoC),
replace BL1 by BL2_EL3 in normal boot mode.
When we recovery images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since LOAD_IMAGE_V2 is always enabled in HiKey platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
After disconnect Jumper pin 1-2 in J15 header, the signal VBUS_DET is to
be pulled down to low level. This will assert the interrupt signal in
PMIC and trigger IRQ in GIC; the asserted signal from VBUS_DET is level
triggered and kernel reports the warning for unhooked interrupt handling;
and VBUS_DET stays with low level, this triggers IRQ storm in kernel.
This patch is to disable interrupt for VBUS_DET in PMIC, this can
dismiss the verbose log and IRQ storm after kernel booting.
[ 40.835279] irq 57: nobody cared (try booting with the "irqpoll" option)
[ 40.842075] CPU: 0 PID: 980 Comm: irq/57-hi655x-p Not tainted 4.4.77-568944-g576a0114dec8-dirty #667
[ 40.851303] Hardware name: HiKey Development Board (DT)
[ 40.856580] Call trace:
[ 40.859060] [<ffffff800808c4cc>] dump_backtrace+0x0/0x1e0
[ 40.864516] [<ffffff800808c8ac>] show_stack+0x20/0x28
[ 40.869622] [<ffffff80084b9688>] dump_stack+0xa8/0xe0
[ 40.874729] [<ffffff800812dd5c>] __report_bad_irq+0x40/0xec
[ 40.880360] [<ffffff800812e0bc>] note_interrupt+0x1e4/0x2d8
[ 40.885992] [<ffffff800812b11c>] handle_irq_event_percpu+0xd8/0x268
[ 40.892324] [<ffffff800812b2f8>] handle_irq_event+0x4c/0x7c
[ 40.897955] [<ffffff800812ecbc>] handle_level_irq+0xcc/0x178
[ 40.903672] [<ffffff800812a778>] generic_handle_irq+0x34/0x4c
[ 40.909481] [<ffffff80085074c8>] pl061_irq_handler+0xa8/0x124
[ 40.915286] [<ffffff800812a778>] generic_handle_irq+0x34/0x4c
[ 40.921092] [<ffffff800812a820>] __handle_domain_irq+0x90/0xf8
[ 40.926985] [<ffffff8008082620>] gic_handle_irq+0x58/0xa8
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Initialize regulators, pins and eMMC in BL1. Only SRAM could be used in BL1.
So BL2 will be loaded from eMMC into SRAM later.
Change-Id: I8e7ef82ffa29a3c647c9d2d2981e8759ee85d833
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Dan Handley <dan.handley@arm.com>
Haojian Zhuang
Victor Chong
Leo Yan