Add an empty line just before the "Build Host" title.
Without this, the title is not properly recognized, it does not get
added to the table of contents and the underlining characters appear
as dashes, as can be seen here:
https://trustedfirmware-a.readthedocs.io/en/v2.7/getting_started/prerequisites.html#prerequisites
Change-Id: Ia89cf3de0588495cbe64b0247dc860619f5ea6a8
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
* changes:
feat(imx8m): keep pu domains in default state during boot stage
feat(imx8m): add the PU power domain support on imx8mm/mn
feat(imx8m): add the anamix pll override setting
feat(imx8m): add the ddr frequency change support for imx8m family
feat(imx8mn): enable dram retention suuport on imx8mn
feat(imx8mm): enable dram retention suuport on imx8mm
feat(imx8m): add dram retention flow for imx8m family
This is an SoM in SODIMM-200 format on an evaluation board called
"DHCOM Premium Developer Kit #2" (DHCOM PDK2 for short). The SoM features an
STM32MP157C SoC with 1 GB DDR3, 8 GB eMMC, microSD and 2 MB SPI flash.
The baseboard has multiple UART, USB, SPI, and I2C ports/headers and several
other interfaces that are not important for TF-A.
These dts(i) files are based on DHCOM dt's from Linux 5.16 and U-Boot 2022.01.
The DRAM calibration values are taken from U-Boot 2022.01 and are optimized for
industrial temperature range above 85° C.
TF-A on this board was fully tested with the latest OP-TEE developer setup.
Change-Id: I696c01742954d761fbad312cd1059e3ab01fa93c
Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Added debug logs to show the reason behind skipping firmware
configuration loading, and also a few debug strings were corrected.
Additionally, a panic will be triggered if the configuration sanity
fails.
Change-Id: I6bbd67b72801e178a14cbe677a8831b25a907d0c
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Neoverse-N2 erratum 2388450 is a cat B erratum that applies to
revision r0p0 and is fixed in r0p1. The workaround is to set
bit[40] of CPUACTLR2_EL1 to disable folding of demand requests into
older prefetches with L2 miss requests outstanding.
SDEN can be found here:
https://developer.arm.com/documentation/SDEN1982442/latest
Change-Id: I6dd949c79cea8dbad322e569aa5de86cf8cf9639
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
The value of the macro CSS_SGI_REMOTE_CHIP_MEM_OFFSET can be different
across all the Neoverse reference design platforms. This value depends
on the number of address bits used per chip. So let all platforms define
CSS_SGI_ADDR_BITS_PER_CHIP which specifies the number of address bits
used per chip.
In addition to this, reuse the definition of CSS_SGI_ADDR_BITS_PER_CHIP
for single chip platforms and CSS_SGI_REMOTE_CHIP_MEM_OFFSET for multi-
chip platforms to determine the maximum address space size. Also,
increase the RD-N2 multi-chip address space per chip from 4TB to 64TB.
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Change-Id: If5e69ec26c2389304c71911729d4addbdf8b2686
The EL3 runtime firmware has been running from internal trusted
SRAM space on the Morello platform. Due to unavailability of tag
support for the internal trusted SRAM this becomes a problem if
we enable capability pointers in BL31.
To support capability pointers in BL31 it has to be run from the
main DDR memory space. This patch updates the Morello platform
configuration such that BL31 is loaded and run from DDR space.
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
Change-Id: I16d4d757fb6f58c364f5133236d50fc06845e0b4
The patch 8c980a4 created a 4KB shared region from the 32MB
Realm region for RMM-EL3 communication. But this meant that BL2
needs to map a region of 32MB - 4KB, which required more xlat
tables at runtime. This patch maps the entire 32MB region in BL2
which is more memory efficient in terms of xlat tables needed.
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Change-Id: I17aa27545293d7b5bbec1c9132ea2c22bf2e7e65
MISRA Violation: MISRA-C:2012 R.10.1
1) The expression of non-boolean essential type is being interpreted as a
boolean value for the operator.
2) The operand to the operator does not have an essentially unsigned type.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I97bbc056f4fee167742429e144144ba793bf77b3
while sbsa maintainers upstream decide whether new cpus types
should be in, add fujitsu a64fx cpu type in advance
Signed-off-by: Itaru Kitayama <itaru.kitayama@fujitsu.com>
Change-Id: I521a62f1233f3fe6e92f040edaff2cc60a1bd874
On STM32MP13, USART1 and USART2 addresses are 0x4C000000 and 0x4C001000.
Whereas on STM32MP15, the addresses were 0x5C000000 and 0x4000E000.
Use dedicated flags to choose the correct address, that could be use
for early or crash console.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I98bd97a0ac8b0408a50376801e2a1961b241a3d6
U-Boot is loaded at the beginning of the DDR:
STM32MP_DDR_BASE = 0xC0000000.
This patch remove the need to use the 0x100000 offset, reserved
on STM32MP15 for flashlayout.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: I8d0a93f4db411cf59838e635a315c729cccee269
* changes:
docs(rmmd): document EL3-RMM Interfaces
feat(rmmd): add support to create a boot manifest
fix(rme): use RMM shared buffer for attest SMCs
feat(rmmd): add support for RMM Boot interface
Due to their interrelationship in the architecture the SVE and SME
features in TF-A are mutually exclusive. This means that a single binary
can't be shared between systems with and without SME if the system
without SME does support SVE, SVE will not be initialised so lower ELs
will run into trouble trying to use it. This unusual behaviour for TF-A
which normally gracefully handles situations where features are enabled
but not supported on the current hardware.
Address this by calling the SVE enable and disable functions if SME is
not supported rather than immediately exiting, these perform their own
feature checks so if neither SVE nor SME is supported behaviour is
unchanged.
Signed-off-by: Mark Brown <broonie@kernel.org>
Change-Id: I2c606202fa6c040069f44e29d36b5abb48391874
This patch documents the RMM-EL3 Boot and runtime interfaces.
Note that for the runtime interfaces, some services are not
documented in this patch and will be added on a later doc patch.
These services are:
* RMMD_GTSI_DELEGATE
* RMMD_GTSI_UNDELEGATE
* RMMD_RMI_REQ_COMPLETE
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I8fcc89d91fe5a334c2f68c6bfd1fd672a8738b5c
This patch also adds an initial RMM Boot Manifest (v0.1) for fvp
platform.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I1374f8f9cb207028f1820953cd2a5cf6d6c3b948
Use the RMM shared buffer to attestation token and signing key SMCs.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I313838b26d3d9334fb0fe8cd4b229a326440d2f4
This patch adds the infrastructure needed to pass boot arguments from
EL3 to RMM and allocates a shared buffer between both worlds that can
be used, among others, to pass a boot manifest to RMM. The buffer is
composed a single memory page be used by a later EL3 <-> RMM interface
by all CPUs.
The RMM boot manifest is not implemented by this patch.
In addition to that, this patch also enables support for RMM when
RESET_TO_BL31 is enabled.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I855cd4758ee3843eadd9fb482d70a6d18954d82a
According to Arm CCA security model [1],
"Root world firmware, including Monitor, is the most trusted CCA
component on application PE. It enforces CCA security guarantees for
not just Realm world, but also for Secure world and for itself.
It is expected to be small enough to feasibly fit in on-chip memory,
and typically needs to be available early in the boot process when
only on-chip memory is available."
For these reasons, it is expected that "monitor code executes entirely
from on-chip memory."
This precludes usage of ARM_BL31_IN_DRAM for RME-enlightened firmware.
[1] Arm DEN0096 A.a, section 7.3 "Use of external memory by CCA".
Change-Id: I752eb45f1e6ffddc7a6f53aadcc92a3e71c1759f
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Validate that non-secure caller does not spoof
SPMD, SPMC or any secure endpoint ID
in FFA_MSG_SEND_DIRECT_REQ.
Change-Id: I7eadb8886142d94bef107cf485462dfcda828895
Signed-off-by: Shruti <shruti.gupta@arm.com>
On STM32MP15, there is currently an OP-TEE shared memory area at the end
of the DDR. But this area will in term be removed. To allow a smooth
transition, a new flag is added (STM32MP15_OPTEE_RSV_SHM). It reflects
the OP-TEE flag: CFG_CORE_RESERVED_SHM. The flag is enabled by default
(no behavior change). It will be set to 0 when OP-TEE is aligned, and
then later be removed.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I91146cd8a26a24be22143c212362294c1e880264
Add dependency between rules to generate SP packages and their dtb files
to ensure the dtb files are built before the sptool attempts to generate
the SP package.
Change-Id: I071806f4aa09f39132e3e1990c91d71dc9acd728
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
* changes:
feat(synquacer): add FWU Multi Bank Update support
feat(synquacer): add TBBR support
feat(synquacer): add BL2 support
refactor(synquacer): move common source files
Add FWU Multi Bank Update support. This reads the platform metadata
and update the FIP base address so that BL2 can load correct BL3X
based on the boot index.
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: Masahisa Kojima <masahisa.kojima@linaro.org>
Cc: Manish V Badarkhe <manish.badarkhe@arm.com>
Cc: Leonardo Sandoval <leonardo.sandoval@linaro.org>
Change-Id: I5d96972bc4b3b9a12a8157117e53a05da5ce89f6
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Manish V Badarkhe
Sandrine Bailleux
Bipin Ravi
Madhukar Pappireddy
Manish Pandey
Johann Neuhauser
Daniel Boulby
Joanna Farley
Vijayenthiran Subramaniam
Manoj Kumar
Soby Mathew
Venkatesh Yadav Abbarapu
Itaru Kitayama
Olivier Deprez
Javier Almansa Sobrino
Yann Gautier
Patrick Delaunay
Mark Brown
Shruti
Yann Gautier
Jassi Brar