The boot device is now checked inside a dedicated rule, that is only
called during BL2 compilation step
Change-Id: Ie7bcd1f166285224b0c042238989a82f7b6105c6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Added a new STM32MP_EMMC_BOOT option, which is used to look for SSBL in
the same eMMC boot partition TF-A booted from at a fixed 256k offset. In
case STM32 image header is not found, the boot process rolls back to a
GPT partition look-up scheme.
Signed-off-by: Vyacheslav Yurkov <uvv.mail@gmail.com>
Change-Id: I85a87dc9ae7f2b915ed8e584be80f4b3588efc48
Add basic SDEI support, implementing the software event 0 only for now.
This already allows hypervisors like Jailhouse to use SDEI for internal
signaling while passing the GICC through to the guest (see also IMX8).
With SDEI on, we overrun the SRAM and need to stay in DRAM. So keep SDEI
off by default.
Co-developed-by: Angelo Ruocco <angeloruocco90@gmail.com>
Signed-off-by: Angelo Ruocco <angeloruocco90@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Change-Id: Ic0d71b4ef0978c0a34393f4e3530ed1e24a39ca2
The io_dummy code and function calls are only used in case BL32 is TF-A
SP_min, and not OP-TEE. This code in bl2_io_storage can then be put under
#ifndef AARCH32_SP_OPTEE.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I52787a775160b335f97547203f653419621f5147
STM32MP1 does not use BL1, the loading of BL2 is done by ROM code. It is
then useless to have an entry BL2_IMAGE_ID in the policies.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I464cedf588114d60522433123f8dbef32ae36818
Fix a remainder from early prototyping. OP-TEE as a secure partition
does not need specific SMC function id pass through to EL3.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I2843d1b9a5eb4c966f82790e1655fb569c2de7d4
The UUID strings used in FW_CONFIG DT are not aligned with UUIDs defined
in include/tools_share/firmware_image_package.h for BL32_EXTRA1 and
TRUSTED_KEY_CERT.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I517f8f9311585931f2cb931e0588414da449b694
The UART code for the A3K platform assumes that UART parent clock rate
is always 25 MHz. This is incorrect, because the xtal clock can also run
at 40 MHz (this is board specific).
The frequency of the xtal clock is determined by a value on a strapping
pin during SOC reset. The code to determine this frequency is already in
A3K's comphy driver.
Move the get_ref_clk() function from the comphy driver to a separate
file and use it for UART parent clock rate determination.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I8bb18a2d020ef18fe65aa06ffa4ab205c71be92e
Macros PLAT_MARVELL_BOOT_UART* and PLAT_MARVELL_CRASH_UART* are defined
to same values. De-duplicate them into PLAT_MARVELL_UART* macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Iae5daf7cad6a971e6f3dbe561df3d0174106ca7f
Macros PLAT_MARVELL_BL31_RUN_UART* are not used since commit
d7c4420cb8 ("plat/marvell: Migrate to multi-console API").
Remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I5ec959ef4de87dcfb332c017ad2599bf8af6ffc3
Morello exhibits the behavior similar to Juno wherein CNTBaseN.CNTFRQ
can be written but does not reflect the value of the CNTFRQ register
in CNTCTLBase frame. This doesn't follow ARM ARM in that the value
updated in CNTCTLBase.CNTFRQ is not reflected in CNTBaseN.CNTFRQ.
Hence enable the workaround (applied to Juno) for Morello that updates
the CNTFRQ register in the Non Secure CNTBaseN frame.
Change-Id: Iabe53bf3c25152052107e08321323e4bde5fbef4
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
Add support for XCK26 silicon which is available on SOM board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: Ic98213328702903af8a79f487a2868f3e6d60338
This patch renames the Matterhorn, Matterhorn ELP, and Klein CPUs to
Cortex A710, Cortex X2, and Cortex A510 respectively.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I056d3114210db71c2840a24562b51caf2546e195
UART parent clock is by default the platform's xtal clock, which is
25 MHz.
The value defined in the driver, though, is 25.8048 MHz. This is a hack
for the suboptimal divisor calculation
Divisor = UART clock / (16 * baudrate)
which does not use rounding division, resulting in a suboptimal value
for divisor if the correct parent clock rate was used.
Change the code for divisor calculation to
Divisor = Round(UART clock / (16 * baudrate))
and change the parent clock rate value to 25 MHz.
The final UART divisor for default baudrate 115200 is not affected by
this change.
(Note that the parent clock rate should not be defined via a macro,
since the xtal clock can also be 40 MHz. This is outside of the scope of
this fix, though.)
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Iaa401173df87aec94f2dd1b38a90fb6ed0bf0ec6
Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].
[1] 13f3c5166f ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Iba0424a5787f9e510a60696d4033db1b49b243b2
Use the macros that are now defined in include/lib/smccc.h.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Ibe3c17acd2482b7779318c8a922a138dcace5554
Use the macros that are now defined in include/lib/smccc.h.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Ie1dbc54569086f6a74206b873fee664b4cdeea36
Use the macros that are now defined in include/lib/smccc.h.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I688a76277b729672835d51fafb68d1d6205b6ae4
The JEDEC information for STMicroelectronics is:
JEDEC_ST_MFID U(0x20)
JEDEC_ST_BKID U(0x0)
And rely on platform functions to get chip IP and revision.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I4fa4ac8bb5583b1871b768decc9fe08e8966ff54
Three functions are exported to get SoC version, SoC device ID, and SoC
name. Those functions are based on reworked existing static functions.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I1f3949062bb488286a9e7a38ffcd1457953dac56
The SGI/RD platforms have been using PSCI state ID format as defined in
PSCI version prior to 1.0. This is being changed and the PSCI extended
state ID format as defined in PSCI version 1.1 is being adapted. In
addition to this, the use of Arm recommended PSCI state ID encoding is
enabled as well.
Change-Id: I2be8a9820987a96b23f4281563b6fa22db48fa5f
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
Update idle flow in case of last read command timeout.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: Idb0552d70d59b23822c38269d0fa9fe9ac0d6975
MTK display port mute/unmute control registers need to be
set in secure world.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Iec73650e937bd20e25c18fa28d55ae29e68b10d3
Use proper offset for IPI data based on offset for IPI0
channel.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
Change-Id: I3070517944dd353c3733aa595df0da030127751a
The PCIe root port is outside of the current RPi
MMIO regions, so we need to adjust the address map.
Given much of the code depends on the legacy IOBASE
lets separate that from the actual MMIO begin/end.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Change-Id: Id65460ae58556bd8826dba08bbad79953e2a7c0b
Add APU iommap settings for reviser, apu_ao and
devapc control wrapper.
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Change-Id: Ie8e6a197c0f440f9e4ee8101202283a2dbf501a6
In iMX8MM it is possible to have two copies of bootloader in
SD/eMMC and switch between them. The switch is triggered either
by the BootROM in case the bootloader image is faulty OR can be
enforced by the user. To trigger that switch the
PERSIST_SECONDARY_BOOT bit should be set in GPR10 SRC register.
As the bit is retained after WARM reset, that permits to control
BootROM behavior regarding what boot image it will boot after
reset: primary or secondary.
This is useful for reliable bootloader A/B updates, as it permits
switching between two copies of bootloader at different offsets of
the same storage.
If the PERSIST_SECONDARY_BOOT is 0, the boot ROM uses address
0x8400 for the primary image. If the PERSIST_SECONDARY_BOOT is 1,
the boot ROM reads that secondary image table from address 0x8200
on the boot media and uses the address specified in the table for
the secondary image.
Secondary Image Table contains the sector of secondary bootloader
image, exluding the offset to that image (explained below in the
note). To generate the Secondary Image Table, use e.g.:
$ printf '\x0\x0\x0\x0\x0\x0\x0\x0\x33\x22\x11'
'\x00\x00\x10\x0\x0\x00\x0\x0\x0'
> /tmp/sit.bin
$ hexdump -vC /tmp/sit.bin
00000000 00 00 00 00
00000004 00 00 00 00
00000008 33 22 11 00 <--- This is the "tag"
0000000c 00 10 00 00 <--- This is the "firstSectorNumber"
00000010 00 00 00 00
You can also use NXP script from [1][2] imx-mkimage tool for
SIT generation. Note that the firstSectorNumber is NOT the offset
of the IVT, but an offset of the IVT decremented by Image Vector
Table offset (Table 6-25. Image Vector Table Offset and Initial
Load Region Size for iMX8MM/MQ), so for secondary SPL copy at
offset 0x1042 sectors, firstSectorNumber must be 0x1000
(0x42 sectors * 512 = 0x8400 bytes offset).
In order to test redundant boot board should be closed and
SD/MMC manufacture mode disabled, as secondary boot is not
supported in the SD/MMC manufacture mode, which can be disabled
by blowing DISABLE_SDMMC_MFG (example for iMX8MM):
> fuse prog -y 2 1 0x00800000
For additional details check i.MX 8M Mini Apllication Processor
Reference Manual, 6.1.5.4.5 Redundant boot support for
expansion device chapter.
[1] https://source.codeaurora.org/external/imx/imx-mkimage/
[2] scripts/gen_sit.sh
Change-Id: I0a5cea7295a4197f6c89183d74b4011cada52d4c
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Added support for HW computed CRC using Arm ACLE intrinsics.
These are built-in intrinsics available for ARMv8.1-A, and
onwards.
These intrinsics are enabled via '-march=armv8-a+crc' compile
switch for ARMv8-A (supports CRC instructions optionally).
HW CRC support is enabled unconditionally in BL2 for all Arm
platforms.
HW CRC calculation is verified offline to ensure a similar
result as its respective ZLib utility function.
HW CRC calculation support will be used in the upcoming
firmware update patches.
Change-Id: Ia2ae801f62d2003e89a9c3e6d77469b5312614b3
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Disable non-invasive debug of secure state for Juno
in release builds. This makes sure that PMU counts
only Non-secure events.
Signed-off-by: Zelalem Aweke <zelalem.aweke@arm.com>
Change-Id: I0d1c3f96f3b4e48360a7211ae55851d65d291025
This patch adds support for the crypto and secure storage secure
partitions for the Total Compute platform. These secure partitions
have to be managed by Hafnium executing at S-EL2
Change-Id: I2df690e3a99bf6bf50e2710994a905914a07026e
Signed-off-by: Davidson K <davidson.kumaresan@arm.com>
AMU counters are used for monitoring the CPU performance. RD-V1-MC
platform has architected AMU available for each core. Enable the use of
AMU by non-secure OS for supporting the use of counters for processor
performance control (ACPI CPPC).
Change-Id: I33be594cee669e7f4031e5e5a371eec7c7451030
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
on i.MX8MP A1 silicon, the OCRAM space is extended to 512K + 64K,
currently, OCRAM @0x960000-0x980000 is reserved for BL31, it will
leave the last 64KB in non-continuous space. To provide a continuous
384KB + 64KB space for generic use, so move the BL31 space to
0x970000-0x990000 range.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Change-Id: I96d572fc0f87f05a60f55e0552a68b6e70f8e7f4
the 'always_on' member should be initialized from 'on'.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Change-Id: I5746ff40075b4fcda2ac7d04a8d7f1269af17e91
Added GPT parser support in BL2 for Arm platforms to get the entry
address and length of the FIP in the GPT image.
Also, increased BL2 maximum size for FVP platform to successfully
compile ROM-enabled build with this change.
Verified this change using a patch:
https://review.trustedfirmware.org/c/ci/tf-a-ci-scripts/+/9654
Change-Id: Ie8026db054966653b739a82d9ba106d283f534d0
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
NOTE: Breaking change to the way UUIDs are stored in the DT
Currently, UUIDs are stored in the device tree as
sequences of 4 integers. There is a mismatch in endianness
between the way UUIDs are represented in memory and the way
they are parsed from the device tree. As a result, we must either
store the UUIDs in little-endian format in the DT (which means
that they do not match up with their string representations)
or perform endianness conversion after parsing them.
Currently, TF-A chooses the second option, with unwieldy
endianness-conversion taking place after reading a UUID.
To fix this problem, and to make it convenient to copy and
paste UUIDs from other tools, change to store UUIDs in string
format, using a new wrapper function to parse them from the
device tree.
Change-Id: I38bd63c907be14e412f03ef0aab9dcabfba0eaa0
Signed-off-by: David Horstmann <david.horstmann@arm.com>
Replaced PLAT_ARM_FIP_BASE and PLAT_ARM_FIP_MAX_SIZE macro with a
generic name PLAT_ARM_FLASH_IMAGE_BASE and PLAT_ARM_FLASH_IMAGE_MAX_SIZE
so that these macros can be reused in the subsequent GPT based support
changes.
Change-Id: I88fdbd53e1966578af4f1e8e9d5fef42c27b1173
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
This new compile option is only for Armada 3720 Development Board. When
it is set to 1 then TF-A will setup PM wake up src configuration.
By default this new option is disabled as it is board specific and no
other A37xx board has PM wake up src configuration.
Currently neither upstream U-Boot nor upstream Linux kernel has wakeup
support for A37xx platforms, so having it disabled does not cause any
issue.
Prior this commit PM wake up src configuration specific for Armada 3720
Development Board was enabled for every A37xx board. After this change it
is enabled only when compiling with build flag A3720_DB_PM_WAKEUP_SRC=1
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I09fea1172c532df639acb3bb009cfde32d3c5766
Add board support for RD-N2 Cfg1 variant of RD-N2 platform. It is a
variant of RD-N2 platform with a reduced interconnect mesh size (3x3)
and core count (8-cores). Its platform variant id is 1.
Change-Id: I34ad35c5a5c1e9b69a658fb92ed00e5bc5fe72f3
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
A Neoverse reference design platform can have two or more variants that
differ in core count, cluster count or other peripherals. To allow reuse
of platform code across all the variants of a platform, introduce build
option CSS_SGI_PLATFORM_VARIANT for Arm Neoverse reference design
platforms. The range of allowed values for the build option is platform
specific. The recommended range is an interval of non negative integers.
An example usage of the build option is
make PLAT=rdn2 CSS_SGI_PLATFORM_VARIANT=1
Change-Id: Iaae79c0b4d0dc700521bf6e9b4979339eafe0359
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
This will help in keeping source file generic and conditional
compilation can be contained in platform provided dt files.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I3c6e0a429073f0afb412b9ba521ce43f880b57fe
sgm775 is an old platform and is no longer maintained by Arm and its
fast model FVP_CSS_SGM-775 is no longer available for download.
This platform is now superseded by Total Compute(tc) platforms.
This platform is now deprecated but the source will be kept for cooling
off period of 2 release cycle before removing it completely.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I8fe1fc3da0c508dba62ed4fc60cbc1642e0f7f2a
mt8195 also uses mt6359p RTC. Revice mt8192 RTC and share the
driver with mt8195.
Change-Id: I20c73f6e0af67ef9d4c3d4e0ff373f93950e07db
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
mt8195 also uses PMIC mt6359p. The only difference is the
pwrap register definition.
Change-Id: I9962263c46187d1344f14f857bf4b51e33aedda0
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Yann Gautier
Vyacheslav Yurkov
Jan Kiszka
Yann Gautier
Olivier Deprez
Pali Rohár
Manoj Kumar
Jiaxin Yu
Venkatesh Yadav Abbarapu
johpow01
Pranav Madhu
Hsin-Hsiung Wang
Flora Fu
Rex-BC Chen
Rajan Vaja
Jeremy Linton
Igor Opaniuk
Manish V Badarkhe
Zelalem
Davidson K
Jacky Bai
David Horstmann
Aditya Angadi
Manish Pandey
Yidi Lin