Notice that aldo1 is typically useful for the Olimex A64 board, where
it powers the PE bank through the vcc-pe line.
Without it, it is not possible to light the user led on PE17, for
instance.
Change-Id: I70588bc977b884b22df87f1b075549cb8925925a
Signed-off-by: Thierry Bultel <thierry.bultel@linatsea.fr>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For somewhat historical reasons we are doing some initial PMIC regulator
setup in BL31, as U-Boot does not (yet) have a PMIC driver. This worked
fine so far, but there is at least one board (OrangePi 3) that gets upset,
because the Ethernet PHY needs some *coordinated* bringup of *two*
regulators.
To avoid custom hacks, let's introduce a build option to keep doing the
regulator setup in TF-A. Defining SUNXI_SETUP_REGULATORS to 0 will break
support for some devices on some boards in U-Boot (Ethernet and HDMI),
but will allow to bring up the OrangePi 3 in Linux correctly. We keep
the default at 1 to not change the behaviour for all other boards.
After U-Boot gained proper PMIC support at some point in the future, we
will probably change the default to 0, to get rid of the less optimal
PMIC code in TF-A.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: Ie8e2583d0396f6eeaae8ffe6b6190f27db63e2a7
If a PMIC regulator has its DT node disabled, leave the regulator off.
Change-Id: I895f740328e8f11d485829c3a89a9b9f8e5644be
Signed-off-by: Roman Beranek <roman.beranek@prusa3d.com>
The DRIVEVBUS power rail of the AXP803 PMIC is mostly used to supply
the USB bus power on micro USB sockets, when used in host mode. As this
is a dynamic operation, and mostly we want micro USB sockets to act in
client mode initially, BL31 should not actually enable this power line.
However, on some boards DRIVEVBUS is used to supply power to normal
USB-A sockets. Failing to activate this line there results in
non-functional USB in U-Boot on those boards.
For that reason we were enabling DRIVEVBUS so far, as it did not seem to
cause any harm to the other boards. However it turns out that on the
Pinephone (and other systems with a battery), actually enabling DRIVEVBUS
unconditionally causes serious problems (reboot loop).
To accommodate both use cases, without reverting to a build time option,
check the default OTG configuration in the devicetree. For boards with
USB-A sockets this is set to "host", on boards with micro-B sockets to
"otg". Depending on this setting, we either enable DRIVEVBUS or leave it
alone.
This fixes TF-A on the Pinephone and potentially other battery powered
devices.
Change-Id: Iec0e07f218b2b4393bf4e05c3386261f8ed19e9f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The function names follow the naming convention used by the existing
ARM SCPI client.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I543bae7d46e206eb405dbedfcf7aeba88a12ca48
Previously, the A64/H5 and H6 platforms' PMIC setup code was entirely
independent. However, some H6 boards also need early regulator setup.
Most of the register interface and all of the device tree traversal code
can be reused between the AXP803 and AXP805. The main difference is the
hardware bus interface, so that part is left to the platforms. The
remainder is moved into a driver.
I factored out the bits that were obviously specific to the AXP803;
additional changes for compatibility with other PMICs can be made as
needed.
The only functional change is that rsb_init() now checks the PMIC's chip
ID register against the expected value. This was already being done in
the H6 version of the code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Icdcf9edd6565f78cccc503922405129ac27e08a2
This adds the new regulator list, as well as changes to make the switch
(equivalent to DC1SW on the AXP803) work on both PMICs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I9a1eac8ddfc54b27096c10a8eebdd51aaf9b8311
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The "Reduced Serial Bus" is an Allwinner specific bus, bearing many
similarities with I2C. It sports a much higher bus frequency, though,
(typically 3 MHz) and requires much less handholding for the typical
task of manipulating slave registers (fire-and-forget).
On most A64 boards this bus is used to connect the PMIC to the SoC.
This driver provides basic primitives to read and write slave registers,
it will be later used by the PMIC code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner 64-bit SoCs all use the Mentor Graphics MI2CV I2C controller
core, with inverted clear quirk.
Add a glue driver for this.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Thierry Bultel
Andre Przywara
Roman Beranek
Samuel Holland
Antonio Nino Diaz
Icenowy Zheng