* changes:
rockchip: rk3399: store actual debug uart information on suspend
rockchip: move dt-coreboot uart distinction into param handling code
rockchip: make uart baudrate configurable
rockchip: px30: add uart5 as option for serial output
This patch modifies crash reporting for AArch64 to provide
aligned output of register dump and GIC registers.
Change-Id: I8743bf1d2d6d56086e735df43785ef28051c5fc3
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Extract clock information for UART, MMC & Watchdog from the clock manager
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I42d3d4ceeaf45788d457472f6ddcd3fe099f0133
The rk3399 suspend code saves and restores the debug uart settings, but
right now always does this for the default uart. Right now this works
only by chance for the majority of rk3399 boards, which do not deviate
from that default.
But both Coreboot as well as U-Boot-based platforms can actually use
different uarts for their output, which can be configured from either
devicetree or Coreboot-variables.
To fix this, just use the stored uart-base information instead of the
default constant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: I1ea059d59a1126f6f8702315df7e620e632b686e
Rockchip platforms can be booted from either u-boot or coreboot.
So far the Coreboot-console was initizalized from a coreboot data struct
in the early_param2 callbacks and dt-based consoles with data from the
rockchip_get_uart_* functions.
But later code may also need this console information for example for
special suspend handling. To make this easy follow a suggestion from
Julius Werner and move the coreboot<->dt distinction into the
rockchip_get_uart_* functions, thus making correct data about the used
uart available to all Rockchip platform code at all times.
This includes a new rockchip_get_uart_clock as well, because while the
dt-platforms right now always just default the rate defined in a constant
Coreboot provides its own field for the clock rate and we don't want to
loose that information for the console init. Similarly the rk_uart_*
variables should move into the non-Coreboot code, to prevent them from
being marked as unused, which also requires the rk_get_uart_* functions
to move below the actual dt-parsing.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: I278d595d2aa6c6864187fc8979a9fbff9814feac
Pull out common code from aarch64 and include
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I4d0f5e1bb01bcdacbedf8e6c359de594239b645f
Coverity has identified that the __aeabi_imod function will loop forever
if the denominator is not a power of 2, which is probably not the
desired behaviour.
The functions in the rest of the file are compiler implementations of
division if ARMv7 does not implement division which is permitted by the
spec. However, while most of the functions in the file are documented
and referenced in other places online, __aeabi_uimod and __aeabi_imod
are not. For this reason, these functions have been removed from the
code base, which also removes the Coverity error.
Change-Id: I20066d72365329a8b03a5536d865c4acaa2139ae
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>
All other returns from this function unlock the responses_lock, so we
also should release the lock in this case.
Change-Id: Ie2cfa8755723fed79e809f9480190d11f373a217
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>
This patch simply splits off the increment of next_xlat into a separate
statement to ensure consistent behaviour if the assert was to ever be
removed.
Change-Id: I827f601ccea55f4da9442048419c9b8cc0c5d22e
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>
This ensures that probe_data starts with a reasonable default, as
opposed to whatever was left on the stack.
Change-Id: I5550efea5e2bec7717f9fa063cb11e6a7005cce5
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>
A previous patch already allowed to configure the uart output from the
devicetree, but on Rockchip platforms we also have the issue of different
vendors using different baudrates for their uarts.
For example, rk3399 has a default baudrate of 115200 which is true for
ChromeOS-devices and boards from Theobroma-Systems, while all the boards
using the vendor boot chain actually use a baudrate of 1500000.
Similarly the newly added px30 has a default of said 1500000 but some
boards may want to use the more widely used 115200.
The devicetree stdout-path node already contains the desired baudrate,
so add simple code to parse it from there and override the default,
which stays unchanged.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: I7412139c3df3073a1996eb508ec08642ec6af90d
Enable dispatcher to save/restore unbanked timer registers. So that
both secure (OP-TEE) and non-secure (Linux) worlds can have independent
access control over timer registers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Change-Id: I4d58d5ff8298587ed478c8433fcbc3aef538d668
The px30 mini-evb can use either uart2 (muxed with the sd-card pins) or
uart5 via its pin header for serial output. Uart5 is especially useful
when needing to boot from the sd-card, where uart2 obviously is not
useable.
So add the uart5 constants and it as uart option for the serial-param
handler.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: Ib88df7a55d761ee104d312c9953a13de3beba1c4
The CPU[1-3] are reset to initial/cold boot state (with their reset
address set to 0x0). In this state the cpus are waiting for another
one to set the reset address to bl31_warm_entrypoint and wake them up.
The CPU0 needs a bit of a workaround as changing the reset address
either through PSCI mailbox or the mmio mapped RVBAR (at 0xda834650)
does not seem to have any effect. Thus the workaround consists in
emulating the other CPUs' behavior with a WFE loop and manually jumping
to bl31_warm_entrypoint when woken back up by another one.
Change-Id: I11265620b5fd0619285e3993253a3f9a3ff6a7a4
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Before CPU enters standby state (wfi), the AP needs to signal the SCP
through PSCI mailbox.
Also at boot time the AP has to wait for the SCP to be ready before
sending the first scpi commands or it can crash.
Change-Id: Iacc99f5bec745ad71922c5ea07ca5b87088133b6
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
NOTE: AARCH32/AARCH64 macros are now deprecated in favor of __aarch64__.
All common C compilers pre-define the same macros to signal which
architecture the code is being compiled for: __arm__ for AArch32 (or
earlier versions) and __aarch64__ for AArch64. There's no need for TF-A
to define its own custom macros for this. In order to unify code with
the export headers (which use __aarch64__ to avoid another dependency),
let's deprecate the AARCH32 and AARCH64 macros and switch the code base
over to the pre-defined standard macro. (Since it is somewhat
unintuitive that __arm__ only means AArch32, let's standardize on only
using __aarch64__.)
Change-Id: Ic77de4b052297d77f38fc95f95f65a8ee70cf200
Signed-off-by: Julius Werner <jwerner@chromium.org>
NOTE: __ASSEMBLY__ macro is now deprecated in favor of __ASSEMBLER__.
All common C compilers predefine a macro called __ASSEMBLER__ when
preprocessing a .S file. There is no reason for TF-A to define it's own
__ASSEMBLY__ macro for this purpose instead. To unify code with the
export headers (which use __ASSEMBLER__ to avoid one extra dependency),
let's deprecate __ASSEMBLY__ and switch the code base over to the
predefined standard.
Change-Id: Id7d0ec8cf330195da80499c68562b65cb5ab7417
Signed-off-by: Julius Werner <jwerner@chromium.org>
At the time of writting, GCC 8.3-2019.03 is the latest version available
on developer.arm.com.
Switch to bare-metal toolchain (arm-eabi-) for AArch32. This allows to
have a finer control on the use of floating-point and SIMD instructions.
Change-Id: I4438401405eae1e5f6d531b0162e8fa06f69135e
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Pull out common code from agilex and stratix10
Signed-off-by: Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: Iddc0a9e6eccb30823d7b15615d5ce9c6bedb2abc
Fix the typo "warn" -> "warm".
Also fix the following checkpatch.pl warnings:
CHECK: Prefer using the BIT macro
CHECK: No space is necessary after a cast
CHECK: Alignment should match open parenthesis
CHECK: Unnecessary parentheses around uniphier_io_policies[image_id].dev_handle
Change-Id: Ic11eea2668c4bf2d1e8f089e6338ba7b7156d80b
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the helper in utils_def.h instead of the own macro.
Change-Id: I527f9e75914d60f66354e365006b960ba5e8cbae
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This change is needed for the platform to compile following the changes
made in commits cbdc72b559 and 3e02c7436c.
Change-Id: I3468dd27f3b4f3095fb82f445d51cd8714311eb7
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
This patch adds gicv3 support for qemu, in order not to break any legacy
use case, gicv2 is still set by default, gicv3 can be selected by
compiling parameter QEMU_USE_GIC_DRIVER=QEMU_GICV3.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: Radoslaw Biernacki <radoslaw.biernacki@linaro.org>
Tested-by: Radoslaw Biernacki <radoslaw.biernacki@linaro.org>
Change-Id: Ic63f38abf16ed3c36aa60e80d50103cf05cf797b
This file moves gicv2 codes to a new separate files, target is to add
gicv3 support later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: Radoslaw Biernacki <radoslaw.biernacki@linaro.org>
Tested-by: Radoslaw Biernacki <radoslaw.biernacki@linaro.org>
Change-Id: I30eb1fda5ea5c2b35d79360c52f46601cbca1bcc
Paul Beesley
Alexei Fedorov
Hadi Asyrafi
Heiko Stuebner
Sandrine Bailleux
Justin Chadwell
Sumit Garg
Remi Pommarel
Julius Werner
Louis Mayencourt
Balint Dobszay
Masahiro Yamada
Ambroise Vincent
Soby Mathew
Hongbo Zhang