This adds the minimal functions and definitions to create a basic
BL31 port for an initial FPGA image, in order for the port to be
uploaded to one the FPGA boards operated by an internal group within
Arm, such that BL31 runs as a payload for an image.
Future changes will enable the port for a wide range of system
configurations running on the FPGA boards to ensure compatibility with
multiple FPGA images.
It is expected that this will replace the FPGA fork of the Linux kernel
bootwrapper by performing similar secure-world initialization and setup
through the use of drivers and other well-established methods, before
passing control to the kernel, which will act as the BL33 payload and
run in EL2NS.
This change introduces a basic, loadable port with the console
initialized by setting the baud rate and base address of the UART as
configured by the Zeus image.
It is a BL31-only port, and RESET_TO_BL31 is enabled to reflect this.
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: I1817ad81be00afddcdbbda1ab70eb697203178e2
This patch provides support for measured boot by adding calculation
of BL2 image hash in BL1 and writing these data in TB_FW_CONFIG DTB.
Change-Id: Ic074a7ed19b14956719c271c805b35d147b7cec1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
To demonstrate communication between SP's two instances of Cactus at
S-EL1 has been used.
This patch replaces Ivy SP with cactus-secondary SP which aligns with
changes in tf-a-tests repository.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Iee84f1f7f023b7c4f23fbc13682a42614a7f3707
When using the SPM Dispatcher, the SPMC sits as a BL32 component
(BL32_IMAGE_ID). The SPMC manifest is passed as the TOS fw config
component (TOS_FW_CONFIG_ID). It defines platform specific attributes
(memory range and physical CPU layout) as well as the attributes for
each secure partition (mostly load address). This manifest is passed
to the SPMC on boot up. An SP package contains the SP dtb in the SPCI
defined partition manifest format. As the SPMC manifest was enriched
it needs an increase of tos_fw-config max-size in fvp_fw_config dts.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Ia1dce00c6c4cbaa118fa56617980d32e2956a94e
Rather than creating entry in plat_arm_mmap array to map the
entire DRAM region in BL31/SP_MIN, only map a smaller region holding
HW_CONFIG DTB. Consequently, an increase in number of sub-translation
tables(level-2 and level-3) i.e., MAX_XLAT_TABLES is necessary to map
the new region in memory.
In order to accommodate the increased code size in BL31 i.e.,
PROGBITS, the max size of BL31 image is increased by 0x1000(4K).
Change-Id: I540b8ee550588e22a3a9fb218183d2ab8061c851
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Merge the previously introduced arm_fconf_io_storage into arm_io_storage. This
removes the duplicate io_policies and functions definition.
This patch:
- replace arm_io_storage.c with the content of arm_fconf_io_storage.c
- rename the USE_FCONF_BASED_IO option into ARM_IO_IN_DTB.
- use the ARM_IO_IN_DTB option to compile out io_policies moved in dtb.
- propagate DEFINES when parsing dts.
- use ARM_IO_IN_DTB to include or not uuid nodes in fw_config dtb.
- set the ARM_IO_IN_DTB to 0 by default for fvp. This ensure that the behavior
of fvp stays the same as it was before the introduction of fconf.
Change-Id: Ia774a96d1d3a2bccad29f7ce2e2b4c21b26c080e
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
This patch introduces the `SPCI_ID_GET` interface which will return the
ID of the calling SPCI component. Returns 0 for requests from the
non-secure world and the SPCI component ID as specified in the manifest
for secure world requests.
Change-Id: Icf81eb1d0e1d7d5c521571e04972b6e2d356e0d1
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Signed-off-by: Marc Bonnici <marc.bonnici@arm.com>
To accommodate the increasing size of the SCP_BL2 binary, the base
address of the memory region allocated to SCP_BL2 has been moved
downwards from its current (mostly) arbitrary address to the beginning
of the non-shared trusted SRAM.
Change-Id: I086a3765bf3ea88f45525223d765dc0dbad6b434
Signed-off-by: Chris Kay <chris.kay@arm.com>
Add CLCD, HDLCD, PCI and VIRTIO devices as source interfaces for TZC
filter unit to enable DMA for these devices.
Change-Id: Ifad2e56b18605311936e03cfcccda573cac7e60a
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
The motivation behind this patch and following patches is to extract
information about the platform in runtime rather than depending on
compile time macros such as FVP_CLUSTER_COUNT. This partially enables
us to use a single binary for a family of platforms which all have
similar hardware capabilities but differ in configurations.
we populate the data structure describing the power domain hierarchy
of the platform dynamically by querying the number of clusters and cpus
using fconf getter APIs. Compile time macro such as FVP_CLUSTER_COUNT
is still needed as it determines the size of related data structures.
Note that the cpu-map node in HW_CONFIG dts represents a logical
hierarchy of power domains of CPU. However, in reality, the power
domains may not have been physically built in such hierarchy.
Change-Id: Ibcbb5ca7b2c969f8ad03ab2eab289725245af7a9
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Create, register( and implicitly invoke) fconf_populate_topology()
function which extracts the topology related properties from dtb into
the newly created fconf based configuration structure 'soc_topology'.
Appropriate libfdt APIs are added to jmptbl.i file for use with USE_ROMLIB
build feature.
A new property which describes the power domain levels is added to the
HW_CONFIG device tree source files.
This patch also fixes a minor bug in the common device tree file
fvp-base-gicv3-psci-dynamiq-common.dtsi
As this file includes fvp-base-gicv3-psci-common.dtsi, it is necessary
to delete all previous cluster node definitons because DynamIQ based
models have upto 8 CPUs in each cluster. If not deleted, the final dts
would have an inaccurate description of SoC topology, i.e., cluster0
with 8 or more core nodes and cluster1 with 4 core nodes.
Change-Id: I9eb406da3ba4732008a66c01afec7c9fa8ef59bf
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Necessary infrastructure added to integrate fconf framework in BL31 & SP_MIN.
Created few populator() functions which parse HW_CONFIG device tree
and registered them with fconf framework. Many of the changes are
only applicable for fvp platform.
This patch:
1. Adds necessary symbols and sections in BL31, SP_MIN linker script
2. Adds necessary memory map entry for translation in BL31, SP_MIN
3. Creates an abstraction layer for hardware configuration based on
fconf framework
4. Adds necessary changes to build flow (makefiles)
5. Minimal callback to read hw_config dtb for capturing properties
related to GIC(interrupt-controller node)
6. updates the fconf documentation
Change-Id: Ib6292071f674ef093962b9e8ba0d322b7bf919af
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Since N1SDP has a system level cache which is an
external LLC enable the NEOVERSE_N1_EXTERNAL_LLC flag.
Change-Id: Idb34274e61e7fd9db5485862a0caa497f3e290c7
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.
Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Added SPMD_SPM_AT_SEL2 build command line parameter.
Set to 1 to run SPM at S-EL2.
Set to 0 to run SPM at S-EL1 (pre-v8.4 or S-EL2 is disabled).
Removed runtime EL from SPM core manifest.
Change-Id: Icb4f5ea4c800f266880db1d410d63fe27a1171c0
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Add load address and UUID in fw config dts for Cactus and Ivy which are
example SP's in tf-test repository.
For prototype purpose these information is added manually but later on
it will be updated at compile time from SP layout file and SP manifests
provided by platform.
Change-Id: I41f485e0245d882c7b514bad41fae34036597ce4
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
This patch fixes incorrect setting for DEVICE1_SIZE
for FVP platforms with more than 8 PEs.
The current value of 0x200000 supports only 8 PEs
and causes exception for FVP platforms with the greater
number of PEs, e.g. FVP_Base_Cortex_A65AEx8 with 16 PEs
in one cluster.
Change-Id: Ie6391509fe6eeafb8ba779303636cd762e7d21b2
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch introduces a build flag which allows the xlat tables
to be mapped in a read-only region within BL31 memory. It makes it
much harder for someone who has acquired the ability to write to
arbitrary secure memory addresses to gain control of the
translation tables.
The memory attributes of the descriptors describing the tables
themselves are changed to read-only secure data. This change
happens at the end of BL31 runtime setup. Until this point, the
tables have read-write permissions. This gives a window of
opportunity for changes to be made to the tables with the MMU on
(e.g. reclaiming init code). No changes can be made to the tables
with the MMU turned on from this point onwards. This change is also
enabled for sp_min and tspd.
To make all this possible, the base table was moved to .rodata. The
penalty we pay is that now .rodata must be aligned to the size of
the base table (512B alignment). Still, this is better than putting
the base table with the higher level tables in the xlat_table
section, as that would cost us a full 4KB page.
Changing the tables from read-write to read-only cannot be done with
the MMU on, as the break-before-make sequence would invalidate the
descriptor which resolves the level 3 page table where that very
descriptor is located. This would make the translation required for
writing the changes impossible, generating an MMU fault.
The caches are also flushed.
Signed-off-by: Petre-Ionut Tudor <petre-ionut.tudor@arm.com>
Change-Id: Ibe5de307e6dc94c67d6186139ac3973516430466
The dualroot chain of trust involves 2 root-of-trust public keys:
- The classic ROTPK.
- The platform ROTPK (a.k.a. PROTPK).
Use the cookie argument as a key ID for plat_get_rotpk_info() to return the
appropriate one. This only applies if we are using the dualroot CoT ; if using
the TBBR one, the behaviour is unchanged.
Change-Id: I400707a87ec01afd5922b68db31d652d787f79bd
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The cookie will be leveraged in the next commit.
Change-Id: Ie8bad275d856d84c27466461cf815529dd860446
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
- Use the development PROTPK if using the dualroot CoT.
Note that unlike the ROTPK, the PROTPK key hash file is not generated
from the key file, instead it has to be provided. This might be
enhanced in the future.
- Define a CoT build flag for the platform code to provide different
implementations where needed.
Change-Id: Iaaf25183b94e77a99a5d8d875831d90c102a97ea
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
When using the new dualroot chain of trust, a new root of trust key is
needed to authenticate the images belonging to the platform owner.
Provide a development one to deploy this on Arm platforms.
Change-Id: I481145e09aa564822d474cb47d38ec211dd24efd
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
A TZC400 controller is placed inline on DRAM channels and regulates
the secure and non-secure accesses to both secure and non-secure
regions of the DRAM memory. Configure each of the TZC controllers
accordingly.
Change-Id: I75f6d13591a7fe9e50ce15c793e35a8018041815
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
For platforms that have two or more TZC400 controllers instantiated,
allow the TZC400 driver to be usable with all those instances.
This is achieved by allowing 'arm_tzc400_setup' function to accept
the base address of the TZC400 controller.
Change-Id: I4add470e6ddb58432cd066145e644112400ab924
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
The base address for second DRAM varies across different platforms.
So allow platforms to define second DRAM by moving Juno/SGM-775 specific
definition of second DRAM base address to Juno/SGM-775 board definition
respectively, SGI/RD specific definition of DRAM 2 base address to SGI
board definition.
Change-Id: I0ecd3a2bd600b6c7019c7f06f8c452952bd07cae
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
A TZC400 can have upto 4 filters and the number of filters instantiated
within a TZC400 is platform dependent. So allow platforms to define the
value of PLAT_ARM_TZC_FILTERS by moving the existing Juno specific
definition of PLAT_ARM_TZC_FILTERS to Juno board definitions.
Change-Id: I67a63d7336595bbfdce3163f9a9473e15e266f40
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
Use CREATE_SEQ helper macro to create sequence of valid chip counts
instead of manually creating the sequence. This allows a scalable
approach to increase the valid chip count sequence in the future.
Change-Id: I5ca7a00460325c156b9e9e52b2bf656a2e43f82d
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
When TF-A is built with RESET_TO_BL31=1 option, BL31 is the
first image to be run and should have all the memory allocated
to it except for the memory reserved for Shared RAM at the start
of Trusted SRAM.
This patch fixes FVP BL31 load address and its image size for
RESET_TO_BL31=1 option. BL31 startup address should be set to
0x400_1000 and its maximum image size to the size of Trusted SRAM
minus the first 4KB of shared memory.
Loading BL31 at 0x0402_0000 as it is currently stated in
'\docs\plat\arm\fvp\index.rst' causes EL3 exception when the
image size gets increased (i.e. building with LOG_LEVEL=50)
but doesn't exceed 0x3B000 not causing build error.
Change-Id: Ie450baaf247f1577112f8d143b24e76c39d33e91
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Adding support for 32MHz UART clock and selecting it as the
default UART clock
Change-Id: I9541eaff70424e85a3b5ee4820ca0e7efb040d2c
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Running checkpatch.pl on the codebase and making required changes
Change-Id: I7d3f8764cef632ab2a6d3c355c68f590440b85b8
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Note: This patch implements in-band messaging protocol only.
ARM has launched a next version of MHU i.e. MHUv2 with its latest
subsystems. The main change is that the MHUv2 is now a distributed IP
with different peripheral views (registers) for the sender and receiver.
Another main difference is that MHUv1 duplex channels are now split into
simplex/half duplex in MHUv2. MHUv2 has a configurable number of
communication channels. There is a capability register (MSG_NO_CAP) to
find out how many channels are available in a system.
The register offsets have also changed for STAT, SET & CLEAR registers
from 0x0, 0x8 & 0x10 in MHUv1 to 0x0, 0xC & 0x8 in MHUv2 respectively.
0x0 0x4 0x8 0xC 0x1F
------------------------....-----
| STAT | | | SET | | |
------------------------....-----
Transmit Channel
0x0 0x4 0x8 0xC 0x1F
------------------------....-----
| STAT | | CLR | | | |
------------------------....-----
Receive Channel
The MHU controller can request the receiver to wake-up and once the
request is removed, the receiver may go back to sleep, but the MHU
itself does not actively put a receiver to sleep.
So, in order to wake-up the receiver when the sender wants to send data,
the sender has to set ACCESS_REQUEST register first in order to wake-up
receiver, state of which can be detected using ACCESS_READY register.
ACCESS_REQUEST has an offset of 0xF88 & ACCESS_READY has an offset
of 0xF8C and are accessible only on any sender channel.
This patch adds necessary changes in a new file required to support the
latest MHUv2 controller. This patch also needs an update in DT binding
for ARM MHUv2 as we need a second register base (tx base) which would
be used as the send channel base.
Change-Id: I1455e08b3d88671a191c558790c503eabe07a8e6
Signed-off-by: Tushar Khandelwal <tushar.khandelwal@arm.com>
Adding support for generating a semi-random number required for
enabling building TF-A with stack protector support.
TF-A for corstone-700 may now be built using ENABLE_STACK_PROTECTOR=all
Change-Id: I03e1be1a8d4e4a822cf286f3b9ad4da4337ca765
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Forced hash generation used to always generate hash via RSA encryption.
This patch changes encryption based on ARM_ROTPK_LOCATION.
Also removes setting KEY_ALG based on ARM_ROTPL_LOCATION - there is no
relation between these two.
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: Id727d2ed06176a243719fd0adfa0cae26c325005
This patch reserves and maps the Trusted DRAM for SPM core execution.
It also configures the TrustZone address space controller to run BL31
in secure DRAM.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I7e1bb3bbc61a0fec6a9cb595964ff553620c21dc
This patch repurposes the TOS FW configuration file as the manifest for
the SPM core component which will reside at the secure EL adjacent to
EL3. The SPM dispatcher component will use the manifest to determine how
the core component must be initialised. Routines and data structure to
parse the manifest have also been added.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Id94f8ece43b4e05609f0a1d364708a912f6203cb
RD-E1-Edge platform consists of two clusters with eight CPUs each and
two processing elements (PE) per CPU. Commit a9fbf13e04 (plat/arm/sgi:
move topology information to board folder) defined the RD-E1-Edge
topology tree to have two clusters with eight CPUs each but PE per CPU
entries were not added. This patch fixes the topology tree accordingly.
Change-Id: I7f97f0013be60e5d51c214fce3962e246bae8a0b
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
In preparation for adding support for Reference Design platforms
which have different base addresses for GIC Distributor or
Redistributor, move GIC related base addresses to individual platform
definition files.
Change-Id: Iecf52b4392a30b86905e1cd047c0ff87d59d0191
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Introduce macro 'CSS_SGI_CHIP_COUNT' to allow Arm CSS platforms with
multi-chip support to define number of chiplets on the platform. By
default, this flag is set to 1 and does not affect the existing single
chip platforms.
For multi-chip platforms, override the default value of
CSS_SGI_CHIP_COUNT with the number of chiplets supported on the
platform. As an example, the command below sets the number of chiplets
to two on the RD-N1-Edge multi-chip platform:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all
Change-Id: If364dc36bd34b30cc356f74b3e97633933e6c8ee
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Include multi-chip-mode parameter in HW_CONFIG dts to let next stage of
boot firmware know about the multi-chip operation mode.
Change-Id: Ic7535c2280fd57180ad14aa0ae277cf0c4d1337b
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
RD-N1-Edge based platforms can operate in dual-chip configuration
wherein two rdn1edge SoCs are connected through a high speed coherent
CCIX link.
This patch adds a function to check if the RD-N1-Edge platform is
operating in multi-chip mode by reading the SID register's NODE_ID
value. If operating in multi-chip mode, initialize GIC-600 multi-chip
operation by overriding the default GICR frames with array of GICR
frames and setting the chip 0 as routing table owner.
The address space of the second RD-N1-Edge chip (chip 1) starts from the
address 4TB. So increase the physical and virtual address space size to
43 bits to accommodate the multi-chip configuration. If the multi-chip
mode configuration is detected, dynamically add mmap entry for the
peripherals memory region of the second RD-N1-Edge SoC. This is required
to let the BL31 platform setup stage to configure the devices in the
second chip.
PLATFORM_CORE_COUNT macro is set to be multiple of CSS_SGI_CHIP_COUNT
and topology changes are added to represent the dual-chip configuration.
In order the build the dual-chip platform, CSS_SGI_CHIP_COUNT macro
should be set to 2:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all
Change-Id: I576cdaf71f0b0e41b9a9181fa4feb7091f8c7bb4
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.
Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.
Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Multi-chip platforms have two or more identical chips connected using a
high speed coherent link. In order to identify such platforms,
add chip_id and multi_chip_mode information in the platform variant
info structure. The values of these two new elements is populated
during boot.
Change-Id: Ie6e89cb33b3f0f408814f6239cd06647053e23ed
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
For SGI-575 and RD platforms, move bl31_platform_setup handler to
individual board files to allow the platforms to perform board specific
bl31 setup.
Change-Id: Ia44bccc0a7f40a155b33909bcb438a0909b20d42
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Currently, an IO setup failure will be ignored on arm platform release
build. Change this to panic instead.
Change-Id: I027a045bce2422b0a0fc4ff9e9d4c6e7bf5d2f98
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change the return type of "arm_io_is_toc_valid()" and
"plat_arm_bl1_fwu_needed()" to bool, to match function behavior.
Change-Id: I503fba211219a241cb263149ef36ca14e3362a1c
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Oliver Swede
Alexei Fedorov
Manish Pandey
Olivier Deprez
Madhukar Pappireddy
Louis Mayencourt
Max Shvetsov
Chris Kay
Aditya Angadi
Chandni Cherukuri
Petre-Ionut Tudor
Sandrine Bailleux
Suyash Pathak
Vijayenthiran Subramaniam
Jimmy Brisson
Vishnu Banavath
Avinash Mehta
Khandelwal
Morten Borup Petersen
Achin Gupta