There has been a breaking change in the communication protocols used
between the AP cores and the SCP on CSS based platforms like Juno.
This means both the AP Trusted Firmware and SCP firmware must be
updated at the same time.
In case the user forgets to update the SCP ROM firmware, this patch
detects when it still uses the previous version of the communication
protocol. It will then output a comprehensive error message that helps
trouble-shoot the issue.
Change-Id: I7baf8f05ec0b7d8df25e0ee53df61fe7be0207c2
The communication protocol used between the AP cores and the SCP
in CSS-based platforms like Juno has undergone a number of changes.
This patch makes the required modifications to the SCP Boot Protocol,
SCPI Protocol and MHU driver code in shared CSS platform code so that
the AP cores are still able to communicate with the SCP.
This patch focuses on the mandatory changes to make it work. The
design of this code needs to be improved but this will come in
a subsequent patch.
The main changes are:
- MHU communication protocol
- The command ID and payload size are no longer written into the
MHU registers directly. Instead, they are stored in the payload
area. The MHU registers are now used only as a doorbell to kick
off messages. Same goes for any command result, the AP has to
pick it up from the payload area.
- SCP Boot Protocol
- The BL3-0 image is now expected to embed a checksum. This
checksum must be passed to the SCP, which uses it to check the
integrity of the image it received.
- The BL3-0 image used to be transferred a block (4KB)
at a time. The SCP now supports receiving up to 128KB at a
time, which is more than the size of the BL3-0 image.
Therefore, the image is now sent in one go.
- The command IDs have changed.
- SCPI Protocol
- The size of the SCPI payload has been reduced down from 512
bytes to 256 bytes. This changes the base address of the
AP-to-SCP payload area.
- For commands that have a response, the response is the same SCPI
header that was sent, except for the size and the status, which
both must be updated appropriately. Success/Failure of a command
is determined by looking at the updated status code.
- Some command IDs have changed.
NOTE: THIS PATCH BREAKS COMPATIBILITY WITH FORMER VERSIONS OF THE SCP
FIRMWARE AND THUS REQUIRES AN UPDATE OF THIS BINARY. THE LATEST SCP
BINARY CAN BE OBTAINED FROM THE ARM CONNECTED COMMUNITY WEBSITE.
Change-Id: Ia5f6b95fe32401ee04a3805035748e8ef6718da7
Move the Juno port from plat/juno to plat/arm/board/juno. Also rename
some of the files so they are consistently prefixed with juno_.
Update the platform makefiles accordingly.
Change-Id: I0af6cb52a5fee7ef209107a1188b76a3c33a2a9f
Major update to the Juno platform port to use the common platform code
in (include/)plat/arm/* and (include/)plat/common/*. This mainly
consists of removing duplicated code but also introduces some small
behavioural changes where there was unnecessary variation between the
FVP and Juno ports. See earlier commit titled `Add common ARM and CSS
platform code` for details.
Also move the ARM SoC specific security setup (i.e. NIC-400 and PCIe
initialization) from BL1 to `plat_arm_security_setup()` in BL2,
where the other security setup is done.
Change-Id: Ic9fe01bae8ed382bfb04fc5839a4cfff332eb124
Move the FVP port from plat/fvp to plat/arm/board/fvp. Also rename
some of the files so they are consistently prefixed with fvp_.
Update the platform makefiles accordingly.
Change-Id: I7569affc3127d66405f1548fc81b878a858e61b7
Major update to the FVP platform port to use the common platform code
in (include/)plat/arm/* and (include/)plat/common/*. This mainly
consists of removing duplicated code but also introduces some small
behavioural changes where there was unnecessary variation between the
FVP and Juno ports. See earlier commit titled `Add common ARM and CSS
platform code` for details.
Also add support for Foundation FVP version 9.1 during FVP config
setup to prevent a warning being emitted in the console.
Change-Id: I254ca854987642ce09d1b924c9fd410a6e13e3bc
This major change pulls out the common functionality from the
FVP and Juno platform ports into the following categories:
* (include/)plat/common. Common platform porting functionality that
typically may be used by all platforms.
* (include/)plat/arm/common. Common platform porting functionality
that may be used by all ARM standard platforms. This includes all
ARM development platforms like FVP and Juno but may also include
non-ARM-owned platforms.
* (include/)plat/arm/board/common. Common platform porting
functionality for ARM development platforms at the board
(off SoC) level.
* (include/)plat/arm/css/common. Common platform porting
functionality at the ARM Compute SubSystem (CSS) level. Juno
is an example of a CSS-based platform.
* (include/)plat/arm/soc/common. Common platform porting
functionality at the ARM SoC level, which is not already defined
at the ARM CSS level.
No guarantees are made about the backward compatibility of
functionality provided in (include/)plat/arm.
Also remove any unnecessary variation between the ARM development
platform ports, including:
* Unify the way BL2 passes `bl31_params_t` to BL3-1. Use the
Juno implementation, which copies the information from BL2 memory
instead of expecting it to persist in shared memory.
* Unify the TZC configuration. There is no need to add a region
for SCP in Juno; it's enough to simply not allow any access to
this reserved region. Also set region 0 to provide no access by
default instead of assuming this is the case.
* Unify the number of memory map regions required for ARM
development platforms, although the actual ranges mapped for each
platform may be different. For the FVP port, this reduces the
mapped peripheral address space.
These latter changes will only be observed when the platform ports
are migrated to use the new common platform code in subsequent
patches.
Change-Id: Id9c269dd3dc6e74533d0e5116fdd826d53946dc8
Some assembly files containing macros are included like header files
into other assembly files. This will cause assembler errors if they
are included multiple times.
Add header guards to assembly macro files to avoid assembler errors.
Change-Id: Ia632e767ed7df7bf507b294982b8d730a6f8fe69
The required platform constant PLATFORM_CACHE_LINE_SIZE is
unnecessary since CACHE_WRITEBACK_GRANULE effectively provides the
same information. CACHE_WRITEBACK_GRANULE is preferred since this
is an architecturally defined term and allows comparison with the
corresponding hardware register value.
Replace all usage of PLATFORM_CACHE_LINE_SIZE with
CACHE_WRITEBACK_GRANULE.
Also, add a runtime assert in BL1 to check that the provided
CACHE_WRITEBACK_GRANULE matches the value provided in CTR_EL0.
Change-Id: If87286be78068424217b9f3689be358356500dcd
In order for the symbol table in the ELF file to contain the size of
functions written in assembly, it is necessary to report it to the
assembler using the .size directive.
To fulfil the above requirements, this patch introduces an 'endfunc'
macro which contains the .endfunc and .size directives. It also adds
a .func directive to the 'func' assembler macro.
The .func/.endfunc have been used so the assembler can fail if
endfunc is omitted.
FixesARM-Software/tf-issues#295
Change-Id: If8cb331b03d7f38fe7e3694d4de26f1075b278fc
Signed-off-by: Kévin Petit <kevin.petit@arm.com>
For Juno r0, the platform reset handler needs to:
- Implement the workaround for defect #831273
- Increase the L2 Data and Tag RAM latencies for Cortex-A57.
Defect #831273 does not affect Juno r1. Also, the default value
for the L2 Tag RAM latency for Cortex-A57 is suitable on Juno r1.
The L2 Data RAM latency for Cortex-A57 still needs to be
increased, though.
This patch modifies the Juno platform reset handler to detect
the board revision and skip the unnecessary steps on Juno r1.
The behaviour on Juno r0 is unchanged.
Change-Id: I27542917223e680ef923ee860900806ffcd0357b
This patch updates the FVP and Juno platform ports to use the common
driver for ARM Cache Coherent Interconnects.
Change-Id: Ib142f456b9b673600592616a2ec99e9b230d6542
This patch defines the ARRAY_SIZE macro for calculating number of elements
in an array and uses it where appropriate.
Change-Id: I72746a9229f0b259323972b498b9a3999731bc9b
Cortex-A57 erratum #806969 applies to revision r0p0 of the CPU
but does not manifest itself on Juno r0. It is not applicable
to Juno r1 in any case.
This patch modifies the Juno platform Makefile to no longer
compile this erratum workaround in.
Change-Id: I32b16835b2ac897e639e869ab2b78b62a51a0139
This patch modifies the declarations of the functions printf() et al.
and adds the right GCC attribute to request the compiler to check
the type of the arguments passed to these functions against the given
format string. This will ensure that the compiler outputs warning
messages like the following whenever it detects an inconsistency:
file.c:42: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘long int’
It also fixes the type mismatch inconsistencies that it revealed
across the code base.
NOTE: THIS PATCH MAY FORCE PLATFORM PORTS OR SP/SPDS THAT USE THE
PRINTF FAMILY OF FUNCTIONS TO FIX ANY TYPE MISMATCH INCONSISTENCIES.
Change-Id: If36bb54ec7d6dd2cb4791d89b02a24ac13fd2df6
All coding style violations have been fixed in a previous patch and
since then, each individual patch has been checked in this regard.
However, the latest version of the checkpatch.pl script from the Linux
kernel is more advanced and it is able to flag new errors in the
Trusted Firmware codebase. This patch fixes them.
Change-Id: I1f332f2440984be85d36b231bb83260368987077
By default the SMMU for the DMA-330 is configured to mark some stream IDs
as always belonging to the Secure world. As a result, if EL1 software turns
the SMMU on, certain Non-Secure accesses get rewritten as Secure, making
them bypass translation and access Secure physical addresses directly.
Since the current Juno board firmware configures the DMA-330 hardware as
Non-Secure, rewrite the SMMU's default SSD table as well to prevent any
unexpected behaviour in EL1.
Change-Id: Iaa81d883eecf28d80eb182b9ce475684bf9c718c
This patch removes the plat_get_max_afflvl() platform API
and instead replaces it with a platform macro PLATFORM_MAX_AFFLVL.
This is done because the maximum affinity level for a platform
is a static value and it is more efficient for it to be defined
as a platform macro.
NOTE: PLATFORM PORTS NEED TO BE UPDATED ON MERGE OF THIS COMMIT
FixesARM-Software/tf-issues#265
Change-Id: I31d89b30c2ccda30d28271154d869060d50df7bf
This patch defines MAX_MMAP_REGIONS separately for each BL stage
as per its requirements. This minimizes the size of the mmap[]
array.
FixesARM-Software/tf-issues#201
Change-Id: I19b15e1a91a8365b2ecf24e2cd71937cb73916b2
This patch adds support to authenticate the Trusted Key certificate
and the BL3-x certificates and images at BL2.
Change-Id: I69a8c13a14c8da8b75f93097d3a4576aed71c5dd
This patch moves fvp_io_setup() to bl2_early_platform_setup() in order
to allow BL2 to use the IO framework before bl2_platform_setup().
Change-Id: I75e1a772ab5f9b4727f6727822a2527c30f3c63d
This patch adds support to authenticate the BL2 content certificate
and image using the authentication module in BL1.
The FIP driver has been extended to include the BL2 certificate
UUID.
FVP and Juno ports include the BL2 certificate FIP file
definition.
Change-Id: I32680e9bd123c8db4a4193c14448c9b32b0e9325
This patch implements an authentication module based on the
PolarSSL library (v1.3.9) to verify the Chain of Trust when
Trusted Boot is enabled.
PolarSSL sources must be fetched separately. The POLARSSL_DIR
build option may be used to indicate the path to the PolarSSL
main directory (this directory must contain the 'include' and
'library' subdirectories).
To be able to build PolarSSL sources as a part of the Trusted
Firmware build process, the DISABLE_PEDANTIC flag in polarssl.mk
will tell the build system to remove the -pedantic option from
the CFLAGS.
Inclusion of PolarSSL increases the memory requirements of the BL1
and BL2 images. The following are the changes made to the FVP and
Juno platforms to cater for this when TRUSTED_BOARD_BOOT is
defined:
Changes on FVP:
- BL1 and BL2 stacks have been increased to 4 KB
- BL1(rw) section has been increased to 32 KB.
- BL2 memory region has been increased to 112 KB
Changes on Juno:
- BL1 and BL2 stacks have been increased to 4 KB
- BL1(rw) section has been increased to 32 KB.
- Trusted ROM region in Flash has been increased to 128 KB.
- BL2 memory region has been increased to 116 KB
Change-Id: Ie87d80d43408eb6239c4acd0ec5ab2120e4e9e80
This patch adds the function plat_match_rotpk() to the platform
porting layer to provide a Root Of Trust Public key (ROTPK)
verification mechanism. This function is called during the
Trusted Board Boot process and receives a supposed valid copy
of the ROTPK as a parameter, usually obtained from an external
source (for instance, a certificate). It returns 0 (success) if
that key matches the actual ROTPK stored in the system or any
other value otherwise.
The mechanism to access the actual ROTPK stored in the system
is platform specific and should be implemented as part of this
function. The format of the ROTPK is also platform specific
(to save memory, some platforms might store a hash of the key
instead of the whole key).
TRUSTED_BOARD_BOOT build option has been added to allow the user
to enable the Trusted Board Boot features. The implementation of
the plat_match_rotpk() funtion is mandatory when Trusted Board
Boot is enabled.
For development purposes, FVP and Juno ports provide a dummy
function that returns always success (valid key). A safe trusted
boot implementation should provide a proper matching function.
Documentation updated accordingly.
Change-Id: I74ff12bc2b041556c48533375527d9e8c035b8c3
This patch adds a tool that generates all the necessary elements
to establish the chain of trust (CoT) between the images.
The tool reads the binary images and signing keys and outputs the
corresponding certificates that will be used by the target at run
time to verify the authenticity of the images.
Note: the platform port must provide the file platform_oid.h. This
file will define the OIDs of the x509 extensions that will be added
to the certificates in order to establish the CoT.
Change-Id: I2734d6808b964a2107ab3a4805110698066a04be
This patch adds support to call the reset_handler() function in BL3-1 in the
cold and warm boot paths when another Boot ROM reset_handler() has already run.
This means the BL1 and BL3-1 versions of the CPU and platform specific reset
handlers may execute different code to each other. This enables a developer to
perform additional actions or undo actions already performed during the first
call of the reset handlers e.g. apply additional errata workarounds.
Typically, the reset handler will be first called from the BL1 Boot ROM. Any
additional functionality can be added to the reset handler when it is called
from BL3-1 resident in RW memory. The constant FIRST_RESET_HANDLER_CALL is used
to identify whether this is the first version of the reset handler code to be
executed or an overridden version of the code.
The Cortex-A57 errata workarounds are applied only if they have not already been
applied.
FixesARM-software/tf-issue#275
Change-Id: Id295f106e4fda23d6736debdade2ac7f2a9a9053
This patch allows the secure payload (BL3-2) to be loaded in the
DRAM region secured by the TrustZone controller (top 16 MB of DRAM1).
The location of BL3-2 can be selected at build time by setting the
build flag FVP_TSP_RAM_LOCATION to one of the following options:
- 'tsram' : Trusted SRAM (this is the default option)
- 'tdram' : Trusted DRAM
- 'dram' : Secure region in DRAM1 (top 16MB configured by the
TrustZone controller)
The number of MMU tables in BL3-2 depends on its location in
memory: 3 in case it is loaded in DRAM, 2 otherwise.
Documentation updated accordingly.
FixesARM-software/tf-issues#212
Change-Id: I371eef3a4159f06a0c9e3c6c1f4c905b2f93803a
This patch allows the platform to validate the power_state and
entrypoint information from the normal world early on in PSCI
calls so that we can return the error safely. New optional
pm_ops hooks `validate_power_state` and `validate_ns_entrypoint`
are introduced to do this.
As a result of these changes, all the other pm_ops handlers except
the PSCI_ON handler are expected to be successful. Also, the PSCI
implementation will now assert if a PSCI API is invoked without the
corresponding pm_ops handler being registered by the platform.
NOTE : PLATFORM PORTS WILL BREAK ON MERGE OF THIS COMMIT. The
pm hooks have 2 additional optional callbacks and the return type
of the other hooks have changed.
FixesARM-Software/tf-issues#229
Change-Id: I036bc0cff2349187c7b8b687b9ee0620aa7e24dc
This patch removes the non-secure entry point information being passed
to the platform pm_ops which is not needed. Also, it removes the `mpidr`
parameter for platform pm hooks which are meant to do power management
operations only on the current cpu.
NOTE: PLATFORM PORTS MUST BE UPDATED AFTER MERGING THIS COMMIT.
Change-Id: If632376a990b7f3b355f910e78771884bf6b12e7
This patch extends the build option `USE_COHERENT_MEMORY` to
conditionally remove coherent memory from the memory maps of
all boot loader stages. The patch also adds necessary
documentation for coherent memory removal in firmware-design,
porting and user guides.
FixesARM-Software/tf-issues#106
Change-Id: I260e8768c6a5c2efc402f5804a80657d8ce38773
This patch moves the bakery locks out of coherent memory to normal memory.
This implies that the lock information needs to be placed on a separate cache
line for each cpu. Hence the bakery_lock_info_t structure is allocated in the
per-cpu data so as to minimize memory wastage. A similar platform per-cpu
data is introduced for the platform locks.
As a result of the above changes, the bakery lock api is completely changed.
Earlier, a reference to the lock structure was passed to the lock implementation.
Now a unique-id (essentially an index into the per-cpu data array) and an offset
into the per-cpu data for bakery_info_t needs to be passed to the lock
implementation.
Change-Id: I1e76216277448713c6c98b4c2de4fb54198b39e0
This patch maps the non-secure region of DRAM1 in the MMU. The
non-secure region comprises the whole DRAM1 (0x80000000 -
0xffffffff) excluding the top 16 MB (0xff000000 - 0xffffffff).
The TrustZone controller configures this 16 MB region as secure
memory, so it can not be accessed in non-secure mode.
The number of MMU tables in BL2 has been increased to 3 because
the new size of the non-secure region in DRAM requires an extra L2
table.
Change-Id: I5ad080c6e181f6b6060e15cebb1d18b7fa128cf5
This patch allows the BL3-1 NOBITS section to overlap the BL1 R/W
section since the former will always be used after the latter.
Similarly, the BL3-2 NOBITS section can overlay the BL2 image
when BL3-2 is loaded in Trusted SRAM.
Due to the current size of the images, there is no actual overlap.
Nevertheless, this reorganization may help to optimise the Trusted
SRAM usage when the images size grows.
Note that because BL3-1 NOBITS section is allowed to overlap the
BL1 R/W section, BL1 global variables will remain valid only until
execution reaches the BL3-1 entry point during a cold boot.
Documentation updated accordingly.
FixesARM-software/tf-issues#254
Change-Id: Id538f4d1c7f1f7858108280fd7b97e138572b879
In both FVP and Juno ports, IRQ #16, which is a PPI, is incorrectly
identified as secure SGI #8 through the constant IRQ_SEC_SGI_8.
This patch removes it.
FixesARM-software/tf-issues#282
Change-Id: I9e52d849611ffcd2b1f28e56dd156c5b217ed63e
This patch reassigns the crash console on Juno and FVP to use the runtime
BL3-1 console. The crash console is changed to SoC UART0 (UART2) from the
previous FPGA UART0 (UART0) on Juno. In FVP, it is changed from UART0 to
UART1.
FixesARM-software/tf-issues#256
Change-Id: I7df54f86ca00ec2652c27261dd66a94c12610816
This patch replaces the usage of the GIC private driver in Juno with
the generic ARM GIC driver. The private driver is no longer necessary
and has been removed from the Juno port.
FixesARM-software/tf-issues#253
Change-Id: I6aaabc252e5e6fb5fcf44ab6d0febd9b38791056
This patch optimizes the Cortex-A57 cluster power down sequence by not
flushing the Level1 data cache. The L1 data cache and the L2 unified
cache are inclusive. A flush of the L2 by set/way flushes any dirty
lines from the L1 as well. This is a known safe deviation from the
Cortex-A57 TRM defined power down sequence. This optimization can be
enabled by the platform through the 'SKIP_A57_L1_FLUSH_PWR_DWN' build
flag. Each Cortex-A57 based platform must make its own decision on
whether to use the optimization.
This patch also renames the cpu-errata-workarounds.md to
cpu-specific-build-macros.md as this facilitates documentation
of both CPU Specific errata and CPU Specific Optimization
build macros.
Change-Id: I299b9fe79e9a7e08e8a0dffb7d345f9a00a71480
This patch deprecates the build option to relocate the shared data
into Trusted DRAM in FVP. After this change, shared data is always
located at the base of Trusted SRAM. This reduces the complexity
of the memory map and the number of combinations in the build
options.
FixesARM-software/tf-issues#257
Change-Id: I68426472567b9d8c6d22d8884cb816f6b61bcbd3
This patch adds support on the Juno platform for entering a wfi in
response to a PSCI CPU_SUSPEND call where the state type is a
standby state.
Change-Id: I0a102dee1f8d2ad936c63ad1d1d3ad001a4a4768
This patch configures the TrustZone Controller in Juno to split
the 2GB DDR-DRAM memory at 0x80000000 into Secure and Non-Secure
regions:
- Secure DDR-DRAM: top 16 MB, except for the last 2 MB which are
used by the SCP for DDR retraining
- Non-Secure DDR-DRAM: remaining DRAM starting at base address
Build option PLAT_TSP_LOCATION selects the location of the secure
payload (BL3-2):
- 'tsram' : Trusted SRAM (default option)
- 'dram' : Secure region in the DDR-DRAM (set by the TrustZone
controller)
The MMU memory map has been updated to give BL2 permission to load
BL3-2 into the DDR-DRAM secure region.
FixesARM-software/tf-issues#233
Change-Id: I6843fc32ef90aadd3ea6ac4c7f314f8ecbd5d07b
This patch replaces direct accesses to the TZC-400 registers by the
appropiate calls to the generic driver available in the Trusted
Firmware in order to initialize the TrustZone Controller.
Functions related to the initialization of the secure memory,
like the TZC-400 configuration, have been moved to a new file
'plat_security.c'. This reorganization makes easier to set up
the secure memory from any BL stage.
TZC-400 initialization has been moved from BL1 to BL2 because BL1
does not access the non-secure memory. It is BL2's responsibility
to enable and configure the TZC-400 before loading the next BL
images.
In Juno, BL3-0 initializes some of the platform peripherals, like
the DDR controller. Thus, BL3-0 must be loaded before configuring
the TrustZone Controller. As a consequence, the IO layer
initialization has been moved to early platform initialization.
FixesARM-software/tf-issues#234
Change-Id: I83dde778f937ac8d2996f7377e871a2e77d9490e
This patch uses the IMAGE_BL<x> constants to create translation tables specific
to a boot loader stage. This allows each stage to create mappings only for areas
in the memory map that it needs.
FixesARM-software/tf-issues#209
Change-Id: Ie4861407ddf9317f0fb890fc7575eaa88d0de51c
This patch avoids the problem of crash reporting mechanism accessing
global data in BSS by 'plat_print_gic_regs' for FVP platforms. Earlier
it depended on the global 'plat_config' object for the GIC Base address
in FVP platforms which would have caused exception if it were accessed
before the BSS was initialized. It is now fixed by dynamically
querying the V2M_SYS_ID to find the FVP model type and accordingly
selecting the appropriate GIC Base address.
This patch also fixes the 'plat_print_gic_regs' to use the correct GIC
Distributor base address for printing GICD_IS_PENDR register values
for both Juno and FVP platforms.
FixesARM-Software/tf-issues#236
Change-Id: I545c7b908b3111419bf27db0575ce86acf86784b
This patch gathers miscellaneous minor fixes to the documentation, and comments
in the source code.
Change-Id: I631e3dda5abafa2d90f464edaee069a1e58b751b
Co-Authored-By: Soby Mathew <soby.mathew@arm.com>
Co-Authored-By: Dan Handley <dan.handley@arm.com>
This patch changes the UART port assignment for various BL stages
so as to make it consistent on the platform ports. The BL1, BL2 and
BL3-1 now uses UART0 on the FVP port and SoC UART0 on the Juno port.
The BL3-2 uses UART2 on the FVP port and FPGA UART0 on the Juno
port.
This provides an interim fix to ARM-software/tf-issues#220 until
support is added for changing the UART port for a BL image between
cold boot and runtime.
Change-Id: Iae5faea90be3d59e41e597b34a902f93e737505a
This patch removes the PRIMARY_CPU definition hardcoded in the
Juno port. Instead, the primary CPU is obtained at runtime by
reading the SCC General Purpose Register 1 (GPR_1), whose value
is copied by the SCP into shared memory during the boot process.
Change-Id: I3981daa92eb7142250712274cf7f655b219837f5
This patch adds the Juno platform specific handlers for PSCI
SYSTEM_OFF and SYSTEM_RESET operations.
Change-Id: Ie389adead533ec2314af44d721b4d0f306147c7d
This patch implements the TSP on Juno. It executes from on-chip Trusted
SRAM.
Also, the other bootloader images (i.e. BL1 R/W, BL2 and BL3-1) have
been moved around. The reason is, although there was enough space
overall to store the TSP in SRAM, there was no contiguous free chunk
of SRAM big enough to hold it.
This patch keeps the overall memory layout (i.e. keeping BL1 R/W at
the bottom, BL2 at the top and BL3-1 in between) but moves the base
addresses of all the bootloader images in such a way that:
- memory fragmentation is reduced enough to fit BL3-2 in;
- new base addresses are suitable for release builds as well as debug
ones;
- each image has a few extra kilobytes for future growth.
BL3-1 and BL3-2 are the images which received the biggest allocations
since they will most probably grow the most.
This patch also adds instruction synchronization barriers around the code which
handles the timer interrupt in the TSP. This ensures that the interrupt is not
acknowledged after or EOIed before it is deactivated at the peripheral.
Change-Id: I1c5b51858700027ee283ac85d18e06863a27c72e
This patch adds support for PSCI CPU_OFF and CPU_SUSPEND APIs to the Juno port
of the ARM Trusted Firmware. The maximum affinity level that can be suspended is
the cluster level (affinity level 1). Support for suspending the system level is
not present.
Change-Id: Ie2c9da0acd7d1b0d5ac64940cdf40347153e52c8
This patch adds the initial port of the ARM Trusted Firmware on the Juno
development platform. This port does not support a BL3-2 image or any PSCI APIs
apart from PSCI_VERSION and PSCI_CPU_ON. It enables workarounds for selected
Cortex-A57 (#806969 & #813420) errata and implements the workaround for a Juno
platform errata (Defect id 831273).
Change-Id: Ib3d92df3af53820cfbb2977582ed0d7abf6ef893
Sandrine Bailleux
Dan Handley
Kévin Petit
Vikram Kanigiri
Robin Murphy
Soby Mathew
Juan Castillo
Yatharth Kochar
Achin Gupta