It is not needed to reserve 64MB for FIP. Limit this to 4MB
for both supported Armada SoC families.
Change-Id: I58a8ce4408a646fe1afd3c1ea1ed54007c8d205d
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[Extract from bigger commit]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Make sure the current CCU window is not in use before adding
a new address map during MSS BL2 image load preparations.
At BL2 stage the CCU Win-2 points to DRAM. If additional mapping is
added to MSS BL2 stage initialization, the DDR entry will be destroyed
and lead to the system hang.
Change-Id: I215e83508acc37d54dab6954d791b9a74cc883ca
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add ccu_is_win_enabled() API for checking the CCU window
state using AP and window indexes.
Change-Id: Ib955a2cac28b2729b0a763f3bbbea28b476a2fe4
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Make all LLC-related macros to start with the same prefix
Add more LLC control registers definitions
This patch is a preparation step for LLC SRAM support
Change-Id: I0a4f0fc83e8ef35be93dd239a85f2a9f88d1ab19
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done after access to each CP is provided.
Moving the proper configuration from BL31 to BL2 solves it.
Change-Id: I44cf88dfd4ebf09130544332bfdd3d16ef2674ea
Signed-off-by: Ben Peled <bpeled@marvell.com>
As a preparation to support proper loading the OPTEE OS image,
enable the BL32 specific defines in case the SPD is used.
On the occasion move two BL32-related macros to marvell_def.h
and fix BL32_LIMIT definition.
Change-Id: Id4e2d81833bc1895650cca8b0fc0bfc341cf77f3
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
The phy porting layer uses defaults defined in
"phy-default-porting-layer.h" when board specific file
"phy-porting-layer.h" is not found. Because of the regression the board
specific directory was not included, therefore all boards used default
parameters.
Change-Id: I66e5e6eb8a39cca5aeeb4de6dab2ceddc39c1e31
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Configuring common phy selector which was missing for AP mode.
Change-Id: I15be1ba50b8aafe9094734abec139d72c18bb224
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
1) Relay only on rx training, remove parts responsible for tx training
(trx training).
2) Add extra steps e.g. preconfigure FFE before starting training.
3) Remove some unnecessary steps like RRBS31 loopback setting which
shouldn't be relevant for tx_training.
Change-Id: Ib1e8567714f9ce33578186a262c339aa4b1c51f2
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Before this patch the configuration took place only for CP0 and CP1, but
since new platforms can contains up to 3 CPs update is required.
Change-Id: Iebd50bbe7b9772063e2c4efb3a7ecbfd593e950d
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
This patch provides the platform level support to enable GICv3
drivers on future Tegra platforms.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I966a4502b2a4a7bd1ce66da843997c9ed605c59f
The previous sequence used by the driver to program the new memory
aperture settings and clear the non-overlapping memory was faulty.
The sequence locked the non-overlapping regions twice, leading to
faults when trying to clear it.
This patch modifies the sequence to follow these steps:
* move the previous memory region to a new firewall register
* program the new memory aperture settings
* clean the non-overlapping memory
This patch also maps the non-overlapping memory as Device memory to
follow guidance from the arch. team.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I7cf6e05b2dd372103dc7229e37b1b3fc269a57ae
The Marvell Armada 37xx SoCs-based platforms contain a bit
awkward directory structure because the currently only one
supported PLAT and PLAT_FAMILY are the same. Modify the latter
to 'a3k' in order to improve it and keep plat/marvell/armada
tree more consistent:
plat/marvell/
├── armada
│ ├── a3k
│ │ ├── a3700
[...]
│ ├── a8k
│ │ ├── a70x0
[...]
Change-Id: I693a6ef88e6ce49a326a3328875c90bbc186066a
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble: ap807: clean-up PLL configuration sequence
ddr: a80x0: add DDR 32-bit mode support
plat: marvell: mci: perform mci link tuning for all mci interfaces
plat: marvell: mci: use more meaningful name for mci link tuning
plat: marvell: a8k: remove wrong or unnecessary comments
plat: marvell: ap807: enable snoop filter for ap807
plat: marvell: ap807: update configuration space of each CP
plat: marvell: ap807: use correct address for MCIx4 register
plat: marvell: add support for PLL 2.2GHz mode
plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
marvell: armada: add extra level in marvell platform hierarchy
This change implements SCMI channels for reading a SCMI message from a
shared memory and call the SCMI message drivers to route the message
to the target platform services.
SMT refers to the shared memory management protocol which is used
to get/put message/response in shared memory. SMT is a 28byte header
stating shared memory state and exchanged protocol data.
The processing entry for a SCMI message can be a secure interrupt
or fastcall SMCCC invocation.
SMT description in this implementation is based on the OP-TEE
project [1] itself based in the SCP-firmware implementation [2].
Link: [1] a58c4d706d
Link: [2] https://github.com/ARM-software/SCP-firmware.git
Change-Id: I416c7dab5c67954c6fe80bae8d8cdfdcda66873e
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds SCMI reset domain protocol support in the SCMI message drivers
as defined in SCMI specification v2.0 [1]. Not all the messages
defined in the specification are supported.
scmi_msg_get_rd_handler() sanitizes the message_id value
against any speculative use of reset domain ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] 56a1f10ed9
Link: [3] https://github.com/ARM-software/SCP-firmware.git
Change-Id: If7cf13de40a815dedb40dcd5af8b6bb6725d9078
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds SCMI clock protocol support in the SCMI message drivers as
defined in SCMI specification v2.0 [1] for clock protocol messages.
Platform can provide one of the plat_scmi_clock_*() handler for the
supported operations set/get state/rate and others.
scmi_msg_get_clock_handler() sanitizes the message_id value
against any speculative use of clock ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] a7a9e3ba71
Link: [3] https://github.com/ARM-software/SCP-firmware.git
Change-Id: Ib56e096512042d4f7b9563d1e4181554eb8ed02c
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
This change introduces drivers to allow a platform to create a basic
SCMI service and register handlers for client request (SCMI agent) on
system resources. This is the first piece of the drivers: an entry
function, the SCMI base protocol support and helpers for create
the response message.
With this change, scmi_process_message() is the entry function to
process an incoming SCMI message. The function expect the message
is already copied from shared memory into secure memory. The message
structure stores message reference and output buffer reference where
response message shall be stored.
scmi_process_message() calls the SCMI protocol driver according to
the protocol ID in the message. The SCMI protocol driver will call
defined platform handlers according to the message content.
This change introduces only the SCMI base protocol as defined in
SCMI specification v2.0 [1]. Not all the messages defined
in the specification are supported.
The SCMI message implementation is derived from the OP-TEE project [2]
itself based on the SCP-firmware implementation [3] of the SCMI protocol
server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] ae8c806809
Link: [3] https://github.com/ARM-software/SCP-firmware/tree/v2.6.0
Change-Id: I639c4154a39fca60606264baf8d32452641f45e9
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Load address of tb_fw_config is incorrectly mentioned
in below device trees:
1. rdn1edge_fw_config.dts
2. tc0_fw_config.dts
Till now, tb_fw_config load-address is not being retrieved from
device tree and hence never exeprienced any issue for tc0 and
rdn1edge platform.
For tc0 and rdn1edge platform, Load-address of tb_fw_config should
be the SRAM base address + 0x300 (size of fw_config device tree)
Hence updated these platform's fw_config.dts accordingly to reflect
this load address change.
Change-Id: I2ef8b05d49be10767db31384329f516df11ca817
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
with sha 44f1aa8, support for Silicon Provider(SiP) owned Secure
Partition(SP) was added for dualroot CoT. This patch extends this
support for tbbr CoT.
Earlier tbbr CoT for SPs was left to avoid adding new image types in
TBBR which could possibly be seen as deviation from specification.
But with further discussions it is understood that TBBR being a
*minimal* set of requirements that can be extended as long as we don't
violate any of the musts, which is the case with adding SP support.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I1b9e3ebdd7d653f1fd4cc3bd910a69871b55ecbb
This patch provides verbose prints for RAS SErrors handled by the
firmware, for improved debugging.
Change-Id: Iaad8d183054d884f606dc4621da2cc6b2375bcf9
Signed-off-by: David Pu <dpu@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch adds a build config 'RAS_TRAP_LOWER_EL_ERR_ACCESS' to set
SCR_EL3.TERR during CPU boot. This bit enables trapping RAS register
accesses from EL1 or EL2 to EL3.
RAS_TRAP_LOWER_EL_ERR_ACCESS is disabled by default.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: Ifb0fb0afedea7dd2a29a0b0491a1161ecd241438
This patch introduces a function ID to clear all the RAS error
records for corrected errors.
Per latest requirement, ARM RAS corrected errors will be reported to
lower ELs via interrupts and cleared via SMC. This patch provides
required function to clear RAS error status.
This patch also sets up all required RAS Corrected errors in order to
route RAS corrected errors to lower ELs.
Change-Id: I554ba1d0797b736835aa27824782703682c91e51
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: David Pu <dpu@nvidia.com>
This patch adds all Tegra194 RAS nodes definitions and support to
handle all uncorrectable RAS errors.
Change-Id: I109b5a8dbca91d92752dc282c4ca30f273c475f9
Signed-off-by: David Pu <dpu@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
with sha 0792dd7, support to generate certificate for Secure
Partitions was added for dualroot CoT only, this patch extends
this support for tbbr CoT.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I451c0333536dd1cbe17861d454bdb0dc7a17c63f
The RK3368 has two clusters of 4 cores and it's cluster id starts at
bit 8 of the MPIDR. To convert from the cluster id (0 or 1) to the
lowest CPU-ID in the respective cluster, we thus need to shift by 6
(i.e. shift by 8 to extract the cluster-id and multiply by 4).
This change is required to ensure the PSCI support can index the
per-cpu entry-address array correctly.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Change-Id: I64a76038f090a85a47067f09f750e96e3946e756
The Denver CPUs implement support for PMUv3 for ARMv8.1 and expect the
PMCR_EL0 to be saved in non-secure context.
This patch disables cycle counter when event counting is prohibited
immediately on entering the secure world to avoid leaking useful
information about the PMU counters. The context saving code later
saves the value of PMCR_EL0 to the non-secure world context.
Verified with 'PMU Leakage' test suite.
******************************* Summary *******************************
> Test suite 'PMU Leakage'
Passed
=================================
Tests Skipped : 2
Tests Passed : 2
Tests Failed : 0
Tests Crashed : 0
Total tests : 4
=================================
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I3675e2b99b44ed23d86e29a5af1b496e80324875
Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.
Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.
This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.
Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
A new certificate "sip-sp-cert" has been added for Silicon Provider(SiP)
owned Secure Partitions(SP). A similar support for Platform owned SP can
be added in future. The certificate is also protected against anti-
rollback using the trusted Non-Volatile counter.
To avoid deviating from TBBR spec, support for SP CoT is only provided
in dualroot.
Secure Partition content certificate is assigned image ID 31 and SP
images follows after it.
The CoT for secure partition look like below.
+------------------+ +-------------------+
| ROTPK/ROTPK Hash |------>| Trusted Key |
+------------------+ | Certificate |
| (Auth Image) |
/+-------------------+
/ |
/ |
/ |
/ |
L v
+------------------+ +-------------------+
| Trusted World |------>| SiP owned SPs |
| Public Key | | Content Cert |
+------------------+ | (Auth Image) |
/ +-------------------+
/ |
/ v|
+------------------+ L +-------------------+
| SP_PKG1 Hash |------>| SP_PKG1 |
| | | (Data Image) |
+------------------+ +-------------------+
. .
. .
. .
+------------------+ +-------------------+
| SP_PKG8 Hash |------>| SP_PKG8 |
| | | (Data Image) |
+------------------+ +-------------------+
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia31546bac1327a3e0b5d37e8b99c808442d5e53f
* changes:
plat: intel: Additional instruction required to enable global timer
plat: intel: Fix CCU initialization for Agilex
plat: intel: Add FPGAINTF configuration to when configuring pinmux
plat: intel: set DRVSEL and SMPLSEL for DWMMC
plat: intel: Fix clock configuration bugs
There are additional instruction needed to enable the global timer.
This fixes the global timer initialization
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Idaf2d23359aacc417e2b7d8cdf1688b5cd17ca98
The CCU initialization loop uses the wrong units, this fixes that. This
also fixes snoop filter register set bits should be used instead of
overwriting the register
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Ia15eeeae5569b00ad84120182170d353ee221b31
The size of buffer currently used to store the FDT passed from U-Boot as
a platform parameter is not large enough to store some RK3399 device
trees. The largest RK3399 device tree currently in U-Boot (for the
Pinebook Pro) is about 70KB in size when passed to TF-A, so increase the
buffer size to 128K which gives some headroom for possibly larger FDTs
in future.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Change-Id: I414caf20683cd47c02ee470dfa988544f3809919
FPGAINTF wasn't enabled when configuring pinmux. This fixes the issue.
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: I5a6aacd504901b8f7327b2f4854b8a77d0c37019
DRVSEL and SMPLSEL needs to be set so that it can properly go into full
speed mode. This needs to be done in EL3 as the registers are secured.
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Ia2f348e7742ff7b76da74d392ef1ce71e2f41677
Marcin Wojtas
Konstantin Porotchkin
Ben Peled
Grzegorz Jaszczyk
Alexei Fedorov
Varun Wadekar
Manish Pandey
Etienne Carriere
Sandrine Bailleux
Etienne Carriere
Manish V Badarkhe
David Pu
Madhukar Pappireddy
Philipp Tomsich
Mark Dykes
Andre Przywara
Tien Hock Loh
Hugh Cole-Baker