Usually, C has no problem up-converting types to larger bit sizes. MISRA
rule 10.7 requires that you not do this, or be very explicit about this.
This resolves the following required rule:
bl1/aarch64/bl1_context_mgmt.c:81:[MISRA C-2012 Rule 10.7 (required)]<None>
The width of the composite expression "0U | ((mode & 3U) << 2U) | 1U |
0x3c0U" (32 bits) is less that the right hand operand
"18446744073709547519ULL" (64 bits).
This also resolves MISRA defects such as:
bl2/aarch64/bl2arch_setup.c:18:[MISRA C-2012 Rule 12.2 (required)]
In the expression "3U << 20", shifting more than 7 bits, the number
of bits in the essential type of the left expression, "3U", is
not allowed.
Further, MISRA requires that all shifts don't overflow. The definition of
PAGE_SIZE was (1U << 12), and 1U is 8 bits. This caused about 50 issues.
This fixes the violation by changing the definition to 1UL << 12. Since
this uses 32bits, it should not create any issues for aarch32.
This patch also contains a fix for a build failure in the sun50i_a64
platform. Specifically, these misra fixes removed a single and
instruction,
92407e73 and x19, x19, #0xffffffff
from the cm_setup_context function caused a relocation in
psci_cpus_on_start to require a linker-generated stub. This increased the
size of the .text section and caused an alignment later on to go over a
page boundary and round up to the end of RAM before placing the .data
section. This sectionn is of non-zero size and therefore causes a link
error.
The fix included in this reorders the functions during link time
without changing their ording with respect to alignment.
Change-Id: I76b4b662c3d262296728a8b9aab7a33b02087f16
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
In the function gicv2_set_spi_routing, the signed value proc_num is cast
to unsigned int before being compared to other unsigned values in two
assert calls. The value proc_num can be a negative value, and once the
negative value is cast to unsigned it becomes a very large number which
will trigger the assert. This patch changes the assert cast so that the
unsigned values are cast to signed instead, keeping the same functionality
but allowing proc_num to be negative.
This bug can be seen when running the SDEI RM_ANY routing mode test in
TFTF on the Juno platform.
This patch also makes the usage of the proc_num variable in other gicv2
functions more clear.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: If1b98eebb00bd9b73862e5e995e5e68c168170a6
And from crash_console_flush.
We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.
Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
A GICv3 interrupt controller will be instantiated for a certain number
of cores. This will result in the respective number of GICR frames. The
last frame will have the "Last" bit set in its GICR_TYPER register.
For platforms with a topology unknown at build time (the Arm FPGAs, for
instance), we need to learn the number of used cores at runtime, to size
the GICR region in the devicetree accordingly.
Add a generic function that iterates over all GICR frames until it
encounters one with the "Last" bit set. It returns the number of cores
the GICv3 has been configured for.
Change-Id: I79f033c50dfc1c275aba7122725868811abcc4f8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch fixes defects 10.3, 10.4, 10.7, 20.7
reported by MISRA-2012 scan and adds braces for
conditional statements according to the TF-A
coding style.
Change-Id: If84ed31cdd55bc8e7cdd2a5f48c0dacc25792112
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
The Arm GIC-Clayton IP has the same power management requirements as
the GIC-600, when it comes to powering up the redistributors before
using them.
Add the IIDR value to the existing list of implementations requiring
the power sequence.
Change-Id: Ib965dfe278c40a4fff94f65a8d445c27a2ae6fd2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch moves all GICv2 driver files into new added
'gicv2.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
NOTE: Usage of 'drivers/arm/gic/common/gic_common.c' file
is now deprecated and platforms with GICv2 driver need to
be modified to include 'drivers/arm/gic/v2/gicv2.mk' in
their makefiles.
Change-Id: Ib10e71bdda0e5c7e80a049ddce2de1dd839602d1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch adds the IIDR value for GIC600-AE to the gicv3_is_gic600()
helper function. This helps platforms supporting this version of the
GIC600 interrupt controller to function with the generic GIC driver.
Verified with tftf-validation test suite
******************************* Summary *******************************
> Test suite 'Framework Validation'
Passed
> Test suite 'Timer framework Validation'
Passed
=================================
Tests Skipped : 0
Tests Passed : 6
Tests Failed : 0
Tests Crashed : 0
Total tests : 6
=================================
NOTICE: Exiting tests.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I518ae7b56f7f372e374e453287d76ca370fc3574
Cleaned up confused naming between TB_FW and FW_CONFIG.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I9e9f6e6ca076d38fee0388f97d370431ae067f08
It is desired to have the peripheral writes completed to clear the
interrupt condition and de-assert the interrupt request to GIC before
EOI write. Failing which spurious interrupt will occurred.
A barrier is needed to ensure peripheral register write transfers are
complete before EOI is done.
GICv2 memory mapped DEVICE nGnR(n)E writes are ordered from core point
of view. However these writes may pass over different interconnects,
bridges, buffers leaving some rare chances for the actual write to
complete out of order.
GICv3 ICC EOI system register writes have no ordering against nGnR(n)E
memory writes as they are over different interfaces.
Hence a dsb can ensure from core no writes are issued before the previous
writes are *complete*.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: Ie6362009e2f91955be99dca8ece14ade7b4811d6
The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.
This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.
Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To support compatibility with previous GICv3 driver version
this patch:
- restores original API for gicr_read_ipriority() and
gicr_wrtite_ipriority() functions;
- adds accessor functions for GICR_XXX0,1 registers, e.g.
GICR_IGROUPR0, GICR_ICFGR0, GICR_ICFGR1, etc.
Change-Id: I796a312a61665ff384e3d9de2f4b3c60f700b43b
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
GIC-Clayton supports multichip operation mode which allows it to connect
upto 16 other GIC-Clayton instances. GIC-Clayton's multichip programming
and operation remains same as GIC-600 with a minor change in the
SPI_BLOCKS and SPI_BLOCK_MIN shifts to accommodate additional SPI
ranges. So identify if the GIC v4 extension is enabled by the platform
makefile and appropriately select the SPI_BLOCKS and SPI_BLOCK_MIN
shifts.
Change-Id: I95fd80ef16af6c7ca09e2335539187b133052d41
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
This patch adds support for GICv4 extension.
New `GIC_ENABLE_V4_EXTN` option passed to gicv3.mk makefile
was added, and enables GICv4 related changes when set to 1.
This option defaults to 0.
Change-Id: I30ebe1b7a98d3a54863900f37eda4589c707a288
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch provides support for GICv3.1 extended PPI and SPI
range. The option is enabled by setting to 1 and passing
`GIC_EXT_INTID` build flag to gicv3.mk makefile.
This option defaults to 0 with no extended range support.
Change-Id: I7d09086fe22ea531c5df51a8a1efd8928458d394
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch moves all GICv3 driver files into new added
'gicv3.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
The patch adds GICv3 driver configuration flags
'GICV3_IMPL', 'GICV3_IMPL_GIC600_MULTICHIP' and
'GICV3_OVERRIDE_DISTIF_PWR_OPS' described in
'GICv3 driver options' section of 'build-option.rst'
document.
NOTE: Platforms with GICv3 driver need to be modified to
include 'drivers/arm/gic/v3/gicv3.mk' in their makefiles.
Change-Id: If055f6770ff20f5dee5a3c99ae7ced7cdcac5c44
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.
Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
The cpu index was wrongly checked causing it to assert always.
Since this code path is exercised only during TF test "NODE_HW_STAT",
which queries Power state from SCP, this bug was not detected earlier.
Change-Id: Ia25cef4c0aa23ed08092df39134937a2601c21ac
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I7a23327394d142af4b293ea7ccd90b843c54587c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Instead, pass back the error to the calling function. This allows
platform code to fall back to another PSCI implementation if
scpi_wait_ready() or a later SCPI command fails.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ib4411e63c2512857f09ffffe1c405358dddeb4a6
On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.
Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.
Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
The Secure Configuration Register is 64-bits in AArch64 and 32-bits in
AArch32. Use u_register_t instead of unsigned int to reflect this.
Change-Id: I51b69467baba36bf0cfaec2595dc8837b1566934
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
NOTE for platform integrators:
API `plat_psci_stat_get_residency()` third argument
`last_cpu_idx` is changed from "signed int" to the
"unsigned int" type.
Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.
2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent
Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.
Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c
The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.
The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
L2 accesses
- manage ACP accesses.
Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.
This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT
Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
As supporting architectures aside from AArch32 and AArch64 is not a
concern, keeping identical definitions in two places for a large part
of the libc seems counterproductive
The int128 types were left un-unified as __int128 is not supported by
gcc on AArch32
Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Change-Id: Idf08e6fab7e4680d9da62d3c57266ea2d80472cf
Arm's GIC-600 features a Power Register (GICR_PWRR),
which needs to be programmed to enable redistributor
operation. Section 3.6.1 in the GIC-600 TRM describes
the power-up and power-down sequence in pseudo code,
which deviates from the current TF-A implementation
in drivers/arm/gic/v3/gic600.c.
For powering on a redistributor, the pseudo code suggests
to loop over the whole sequence (check for transition,
write request bit) instead of just looping over the
ready bit read as TF-A does in gic600_pwr_on().
This patch fixes GIC-600 power up sequence according
to the TRM.
Change-Id: I445c480e96ba356b69a2d8e5308ffe6c0a97f45b
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Add support to configure GIC-600's multichip routing table registers.
Introduce a new gic600 multichip structure in order to support platforms
to pass their GIC-600 multichip information such as routing table owner,
SPI blocks ownership.
This driver is currently experimental and the driver api may change in
the future.
Change-Id: Id409d0bc07843e271ead3fc2f6e3cb38b317878d
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Instead of retry polling, timer of 1ms is used to poll
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: I7e028dc68138d2888e3cf0cbed744f5e6bc6ff42
Currently for Armv7 plaforms the quotient calculated in pl011
uart init code is moved to register r1.
This patch moves the quotient to register r2 as done for other
platforms in the udiv instruction. Value of register r2 is then
used to calculate the values for IBRD and FBRD register
Change-Id: Ie6622f9f0e6d634378b471df5d02823b492c8a24
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>
This patch provides declaration and definition of new GICv3 driver
API: gicv3_rdistif_probe().This function delegates the responsibility
of discovering the corresponding Redistributor base frame to each CPU
itself. It is a modified version of gicv3_rdistif_base_addrs_probe()
and is executed by each CPU in the platform unlike the previous
approach in which only the Primary CPU did the discovery of all the
Redistributor frames for every CPU.
The flush operations as part of gicv3_driver_init() function are
made necessary even for platforms with WARMBOOT_ENABLE_DCACHE_EARLY
because the GICv3 driver data structure contents are accessed by CPU
with D-Cache turned off during power down operations.
Change-Id: I1833e81d3974b32a3e4a3df4766a33d070982268
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
This patch fixes GICv3 driver bug which causes assertion
when full range of SPI INTIDs 32-1019 is supported in
GICv3 implementation.
Change-Id: Ib6da4b6eea868cff271cb32c7c7570bf5547ab47
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
NOTE: AARCH32/AARCH64 macros are now deprecated in favor of __aarch64__.
All common C compilers pre-define the same macros to signal which
architecture the code is being compiled for: __arm__ for AArch32 (or
earlier versions) and __aarch64__ for AArch64. There's no need for TF-A
to define its own custom macros for this. In order to unify code with
the export headers (which use __aarch64__ to avoid another dependency),
let's deprecate the AARCH32 and AARCH64 macros and switch the code base
over to the pre-defined standard macro. (Since it is somewhat
unintuitive that __arm__ only means AArch32, let's standardize on only
using __aarch64__.)
Change-Id: Ic77de4b052297d77f38fc95f95f65a8ee70cf200
Signed-off-by: Julius Werner <jwerner@chromium.org>
NOTE: __ASSEMBLY__ macro is now deprecated in favor of __ASSEMBLER__.
All common C compilers predefine a macro called __ASSEMBLER__ when
preprocessing a .S file. There is no reason for TF-A to define it's own
__ASSEMBLY__ macro for this purpose instead. To unify code with the
export headers (which use __ASSEMBLER__ to avoid one extra dependency),
let's deprecate __ASSEMBLY__ and switch the code base over to the
predefined standard.
Change-Id: Id7d0ec8cf330195da80499c68562b65cb5ab7417
Signed-off-by: Julius Werner <jwerner@chromium.org>
This interface has been deprecated in favour of MULTI_CONSOLE_API.
Change-Id: I6170c1c8c74a890e5bd6d05396743fe62024a08a
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
According to Arm GIC spec(IHI0069E, section 4.6.1),
when GICD_CTLR.DS == 0, Secure Group 1 interrupts
are treated as Group 0 by a CPU interface if:
- The PE does not implement EL3.
- ICC_SRE_EL1(S).SRE == 0
When a cpu enter suspend or deep idle, it might be
powered off. When the cpu resume, according to
the GIC spec(IHI0069E, section 9.2.15, 9.2.16 and
9.2.22) the ICC_SRE_EL1.SRE reset value is 0 (if
write is allowed) and G0/G1S/G1NS interrupt of the
GIC cpu interface are all disabled.
If a G1S SPI interrupt occurred and the target cpu
of the SPI is assigned to a specific cpu which is
in suspend and is powered off, when the cpu resume
and start to initial the GIC cpu interface, the
initial sequence might affect the interrupt group
type of the pending interrupt on the cpu interface.
Current initial sequence on the cpu interface is:
1. Enable G0 interrupt
2. Enable G1S interrupt
3. Enable ICC_SRE_EL1(S).SRE
It is possible to treat the pending G1S interrupt
as G0 interrupt on the cpu interface if the G1S
SPI interrupt occurred between step2 and step3.
To prevent the above situation happend, the initial
sequence should be changed as follows:
1. Enable ICC_SRE_EL1(S).SRE
2. Enable G0 interrupt
3. Enable G1S interrupt
Change-Id: Ie34f6e0b32eb9a1677ff72571fd4bfdb5cae25b0
Signed-off-by: James Kung <kong1191@gmail.com>
Payload length of the get dram mapping information message is 0.
The mbx_mem->len parameter should be 4, it only contains
message header.
Fixes: b67d202 ("plat/synquacer: enable SCMI support")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Change-Id: If1cd4c855da2dc5dc4b6da3bea152b8441971de7
For security DMA should be blocked at the SMMU by default
unless explicitly enabled for a device. SMMU is disabled
after reset with all streams bypassing the SMMU, and
abortion of all incoming transactions implements a default
deny policy on reset.
This patch also moves "bl1_platform_setup()" function from
arm_bl1_setup.c to FVP platforms' fvp_bl1_setup.c and
fvp_ve_bl1_setup.c files.
Change-Id: Ie0ffedc10219b1b884eb8af625bd4b6753749b1a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch is a preparation for the subsequent changes in
SMMUv3 driver. It introduces a new "smmuv3_poll" function
and replaces inline functions for accessing SMMU registers
with mmio read/write operations. Also the infinite loop
for the poll has been replaced with a counter based timeout.
Change-Id: I7a0547beb1509601f253e126b1a7a6ab3b0307e7
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Add a driver for configuring the SBSA Generic Watchdog which aids in
the detection of errant system behaviour.
Change-Id: I5a1e7149c69fd8b85be7dfbcf511f431339946f4
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Types tzc_action_t and tzc_region_attributes_t are deprecated.
Change-Id: Ieefeb8521a0e1130f39d09b5c0d2728f05084773
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
The old version of the macro is deprecated.
Commit cc5859ca19 ("Multi-console: Deprecate the
`finish_console_register` macro") provides more details.
Change-Id: I3d1cdf6496db7d8e6cfbb5804f508ff46ae7e67e
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Improved support for W=2 compilation flag by solving some nested-extern
and sign-compare warnings.
The libraries are compiling with warnings (which turn into errors with
the Werror flag).
Outside of libraries, some warnings cannot be fixed.
Change-Id: I06b1923857f2a6a50e93d62d0274915b268cef05
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Enable the SCMI protocol support in SynQuacer platform.
Aside from power domain, system power and apcore management protocol,
this commit adds the vendor specific protocol(0x80).
This vendor specific protocol is used to get the dram mapping information
from SCP.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Fix some typos and clarify some sentences.
Change-Id: Id276d1ced9a991b4eddc5c47ad9a825e6b29ef74
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Cortex a5 doesnt support hardware division such as sdiv and udiv commands.
This commit adds a software division function in assembly as well as include
appropriate files for software divison.
The software division algorithm is a modified version obtained from:
http://www.keil.com/support/man/docs/armasm/armasm_dom1359731155623.htm
Change-Id: Ib405a330da5f1cea1e68e07e7b520edeef9e2652
Signed-off-by: Usama Arif <usama.arif@arm.com>
Jimmy Brisson
johpow01
Andre Przywara
Alexei Fedorov
Varun Wadekar
Manish V Badarkhe
Sandeep Tripathy
Vijayenthiran Subramaniam
Manish Pandey
Samuel Holland
Aditya Angadi
Zelalem
Louis Mayencourt
Deepika Bhavnani
Vishnu Banavath
Bence Szépkúti
Max Shvetsov
Avinash Mehta
Madhukar Pappireddy
Julius Werner
Ambroise Vincent
James kung
Masahisa Kojima
Antonio Nino Diaz
Usama Arif