micropython/cc3200/hal/crc.c

//*****************************************************************************
//
//  crc.c
//
//  Driver for the CRC module.
//
//  Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
//
//
//  Redistribution and use in source and binary forms, with or without
//  modification, are permitted provided that the following conditions
//  are met:
//
//    Redistributions of source code must retain the above copyright
//    notice, this list of conditions and the following disclaimer.
//
//    Redistributions in binary form must reproduce the above copyright
//    notice, this list of conditions and the following disclaimer in the
//    documentation and/or other materials provided with the
//    distribution.
//
//    Neither the name of Texas Instruments Incorporated nor the names of
//    its contributors may be used to endorse or promote products derived
//    from this software without specific prior written permission.
//
//  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
//  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
//  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
//  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
//  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
//  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
//  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
//  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
//  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
//  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
//  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
//*****************************************************************************

//*****************************************************************************
//
//! \addtogroup CRC_Cyclic_Redundancy_Check_api
//! @{
//
//*****************************************************************************

#include <stdbool.h>
#include <stdint.h>
#include "inc/hw_dthe.h"
#include "inc/hw_memmap.h"
#include "inc/hw_types.h"
#include "crc.h"
#include "debug.h"

//*****************************************************************************
//
//! Set the configuration of CRC functionality with the EC module.
//!
//! \param ui32Base is the base address of the EC module.
//! \param ui32CRCConfig is the configuration of the CRC engine.
//!
//! This function configures the operation of the CRC engine within the EC
//! module.  The configuration is specified with the \e ui32CRCConfig argument.
//! It is the logical OR of any of the following options:
//!
//! CRC Initialization Value
//! - \b EC_CRC_CFG_INIT_SEED - Initialize with seed value
//! - \b EC_CRC_CFG_INIT_0 - Initialize to all '0s'
//! - \b EC_CRC_CFG_INIT_1 - Initialize to all '1s'
//!
//! Input Data Size
//! - \b EC_CRC_CFG_SIZE_8BIT - Input data size of 8 bits
//! - \b EC_CRC_CFG_SIZE_32BIT - Input data size of 32 bits
//!
//! Post Process Reverse/Inverse
//! - \b EC_CRC_CFG_RESINV - Result inverse enable
//! - \b EC_CRC_CFG_OBR - Output reverse enable
//!
//! Input Bit Reverse
//! - \b EC_CRC_CFG_IBR - Bit reverse enable
//!
//! Endian Control
//! - \b EC_CRC_CFG_ENDIAN_SBHW - Swap byte in half-word
//! - \b EC_CRC_CFG_ENDIAN_SHW - Swap half-word
//!
//! Operation Type
//! - \b EC_CRC_CFG_TYPE_P8005 - Polynomial 0x8005
//! - \b EC_CRC_CFG_TYPE_P1021 - Polynomial 0x1021
//! - \b EC_CRC_CFG_TYPE_P4C11DB7 - Polynomial 0x4C11DB7
//! - \b EC_CRC_CFG_TYPE_P1EDC6F41 - Polynomial 0x1EDC6F41
//! - \b EC_CRC_CFG_TYPE_TCPCHKSUM - TCP checksum
//!
//! \return None.
//
//*****************************************************************************
void
CRCConfigSet(uint32_t ui32Base, uint32_t ui32CRCConfig)
{
    //
    // Check the arguments.
    //
    ASSERT(ui32Base == DTHE_BASE);
    ASSERT((ui32CRCConfig & CRC_CFG_INIT_SEED) ||
           (ui32CRCConfig & CRC_CFG_INIT_0) ||
           (ui32CRCConfig & CRC_CFG_INIT_1) ||
           (ui32CRCConfig & CRC_CFG_SIZE_8BIT) ||
           (ui32CRCConfig & CRC_CFG_SIZE_32BIT) ||
           (ui32CRCConfig & CRC_CFG_RESINV) ||
           (ui32CRCConfig & CRC_CFG_OBR) ||
           (ui32CRCConfig & CRC_CFG_IBR) ||
           (ui32CRCConfig & CRC_CFG_ENDIAN_SBHW) ||
           (ui32CRCConfig & CRC_CFG_ENDIAN_SHW) ||
           (ui32CRCConfig & CRC_CFG_TYPE_P8005) ||
           (ui32CRCConfig & CRC_CFG_TYPE_P1021) ||
           (ui32CRCConfig & CRC_CFG_TYPE_P4C11DB7) ||
           (ui32CRCConfig & CRC_CFG_TYPE_P1EDC6F41) ||
           (ui32CRCConfig & CRC_CFG_TYPE_TCPCHKSUM));

    //
    // Write the control register with the configuration.
    //
    HWREG(ui32Base + DTHE_O_CRC_CTRL) = ui32CRCConfig;
}

//*****************************************************************************
//
//! Write the seed value for CRC operations in the EC module.
//!
//! \param ui32Base is the base address of the EC module.
//! \param ui32Seed is the seed value.
//!
//! This function writes the seed value for use with CRC operations in the
//! EC module.  This value is the start value for CRC operations.  If this
//! value is not written, then the residual seed from the previous operation
//! is used as the starting value.
//!
//! \note The seed must be written only if \b EC_CRC_CFG_INIT_SEED is
//! set with the CRCConfigSet() function.
//
//*****************************************************************************
void
CRCSeedSet(uint32_t ui32Base, uint32_t ui32Seed)
{
    //
    // Check the arguments.
    //
    ASSERT(ui32Base == DTHE_BASE);

    //
    // Write the seed value to the seed register.
    //
    HWREG(ui32Base + DTHE_O_CRC_SEED) = ui32Seed;
}

//*****************************************************************************
//
//! Write data into the EC module for CRC operations.
//!
//! \param ui32Base is the base address of the EC module.
//! \param ui32Data is the data to be written.
//!
//! This function writes either 8 or 32 bits of data into the EC module for
//! CRC operations.  The distinction between 8 and 32 bits of data is made
//! when the \b EC_CRC_CFG_SIZE_8BIT or \b EC_CRC_CFG_SIZE_32BIT flag
//! is set using the CRCConfigSet() function.
//!
//! When writing 8 bits of data, ensure the data is in the least signficant
//! byte position.  The remaining bytes should be written with zero.  For
//! example, when writing 0xAB, \e ui32Data should be 0x000000AB.
//!
//! \return None
//
//*****************************************************************************
void
CRCDataWrite(uint32_t ui32Base, uint32_t ui32Data)
{
    //
    // Check the arguments.
    //
    ASSERT(ui32Base == DTHE_BASE);

    //
    // Write the data
    //
    HWREG(DTHE_BASE + DTHE_O_CRC_DIN) = ui32Data;
}

//*****************************************************************************
//
//! Reads the result of a CRC operation in the EC module.
//!
//! \param ui32Base is the base address of the EC module.
//!
//! This function reads either the unmodified CRC result or the post
//! processed CRC result from the EC module.  The post-processing options
//! are selectable through \b EC_CRC_CFG_RESINV and \b EC_CRC_CFG_OBR
//! parameters in the CRCConfigSet() function.
//!
//! \return The CRC result.
//
//*****************************************************************************
uint32_t
CRCResultRead(uint32_t ui32Base)
{
    //
    // Check the arguments.
    //
    ASSERT(ui32Base == DTHE_BASE);

    //
    // return value.
    //
    return(HWREG(DTHE_BASE + DTHE_O_CRC_RSLT_PP));

}

//*****************************************************************************
//
//! Process data to generate a CRC with the EC module.
//!
//! \param ui32Base is the base address of the EC module.
//! \param puiDataIn is a pointer to an array of data that is processed.
//! \param ui32DataLength is the number of data items that are processed
//! to produce the CRC.
//! \param ui32Config the config parameter to determine the CRC mode
//!
//! This function processes an array of data to produce a CRC result.
//! This function takes the CRC mode as the parameter.
//!
//! The data in the array pointed to be \e pui32DataIn is either an array
//! of bytes or an array or words depending on the selection of the input
//! data size options \b EC_CRC_CFG_SIZE_8BIT and
//! \b EC_CRC_CFG_SIZE_32BIT.
//!
//! This function returns either the unmodified CRC result or the
//! post- processed CRC result from the EC module.  The post-processing
//! options are selectable through \b EC_CRC_CFG_RESINV and
//! \b EC_CRC_CFG_OBR parameters.
//!
//! \return The CRC result.
//
//*****************************************************************************
uint32_t
CRCDataProcess(uint32_t ui32Base, void *puiDataIn,
               uint32_t ui32DataLength, uint32_t ui32Config)
{
    uint8_t *pui8DataIn;
    uint32_t *pui32DataIn;

    //
    // Check the arguments.
    //
    ASSERT(ui32Base == DTHE_BASE);

    //
    // See if the CRC is operating in 8-bit or 32-bit mode.
    //
    if(ui32Config & DTHE_CRC_CTRL_SIZE)
    {
        //
        // The CRC is operating in 8-bit mode, so create an 8-bit pointer to
        // the data.
        //
        pui8DataIn = (uint8_t *)puiDataIn;

        //
        // Loop through the input data.
        //
        while(ui32DataLength--)
        {
            //
            // Write the next data byte.
            //
            HWREG(ui32Base + DTHE_O_CRC_DIN) = *pui8DataIn++;
        }
    }
    else
    {
        //
        // The CRC is operating in 32-bit mode, so loop through the input data.
        //
    	pui32DataIn = (uint32_t *)puiDataIn;
        while(ui32DataLength--)
        {
            //
            // Write the next data word.
            //
            HWREG(ui32Base + DTHE_O_CRC_DIN) = *pui32DataIn++;
        }
    }

    //
    // Return the result.
    //
    return(CRCResultRead(ui32Base));
}



//*****************************************************************************
//
// Close the Doxygen group.
//! @}
//
//*****************************************************************************