Browse Source
Tweaked a couple of the USB files to compile if neither dev nor host was defined. Tested on netduiono plus 2 and stm32f4discovery boardspull/346/head
Dave Hylands
11 years ago
14 changed files with 434 additions and 32 deletions
@ -0,0 +1,394 @@ |
|||
/**
|
|||
****************************************************************************** |
|||
* @file stm32f4xx_hal_conf.h |
|||
* @author MCD Application Team |
|||
* @version V1.0.1 |
|||
* @date 26-February-2014 |
|||
* @brief HAL configuration file. |
|||
****************************************************************************** |
|||
* @attention |
|||
* |
|||
* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> |
|||
* |
|||
* Redistribution and use in source and binary forms, with or without modification, |
|||
* are permitted provided that the following conditions are met: |
|||
* 1. Redistributions of source code must retain the above copyright notice, |
|||
* this list of conditions and the following disclaimer. |
|||
* 2. Redistributions in binary form must reproduce the above copyright notice, |
|||
* this list of conditions and the following disclaimer in the documentation |
|||
* and/or other materials provided with the distribution. |
|||
* 3. Neither the name of STMicroelectronics nor the names of its contributors |
|||
* may be used to endorse or promote products derived from this software |
|||
* without specific prior written permission. |
|||
* |
|||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
|||
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
|||
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
|||
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE |
|||
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
|||
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR |
|||
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER |
|||
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, |
|||
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
|||
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
|||
* |
|||
****************************************************************************** |
|||
*/ |
|||
|
|||
/* Define to prevent recursive inclusion -------------------------------------*/ |
|||
#ifndef __STM32F4xx_HAL_CONF_H |
|||
#define __STM32F4xx_HAL_CONF_H |
|||
|
|||
#ifdef __cplusplus |
|||
extern "C" { |
|||
#endif |
|||
|
|||
/* Exported types ------------------------------------------------------------*/ |
|||
/* Exported constants --------------------------------------------------------*/ |
|||
|
|||
#define STM32F405xx |
|||
#define USE_USB_FS |
|||
#define USE_USB_OTG_ID 0 |
|||
|
|||
/* ########################## Module Selection ############################## */ |
|||
/**
|
|||
* @brief This is the list of modules to be used in the HAL driver |
|||
*/ |
|||
#define HAL_MODULE_ENABLED |
|||
#define HAL_ADC_MODULE_ENABLED |
|||
#define HAL_CAN_MODULE_ENABLED |
|||
#define HAL_CRC_MODULE_ENABLED |
|||
#define HAL_CRYP_MODULE_ENABLED |
|||
#define HAL_DAC_MODULE_ENABLED |
|||
#define HAL_DCMI_MODULE_ENABLED |
|||
#define HAL_DMA_MODULE_ENABLED |
|||
/* #define HAL_DMA2D_MODULE_ENABLED */ |
|||
#define HAL_ETH_MODULE_ENABLED |
|||
#define HAL_FLASH_MODULE_ENABLED |
|||
#define HAL_NAND_MODULE_ENABLED |
|||
#define HAL_NOR_MODULE_ENABLED |
|||
#define HAL_PCCARD_MODULE_ENABLED |
|||
#define HAL_SRAM_MODULE_ENABLED |
|||
/* #define HAL_SDRAM_MODULE_ENABLED */ |
|||
#define HAL_HASH_MODULE_ENABLED |
|||
#define HAL_GPIO_MODULE_ENABLED |
|||
#define HAL_I2C_MODULE_ENABLED |
|||
#define HAL_I2S_MODULE_ENABLED |
|||
#define HAL_IWDG_MODULE_ENABLED |
|||
#define HAL_LTDC_MODULE_ENABLED |
|||
#define HAL_PWR_MODULE_ENABLED |
|||
#define HAL_RCC_MODULE_ENABLED |
|||
#define HAL_RNG_MODULE_ENABLED |
|||
#define HAL_RTC_MODULE_ENABLED |
|||
/* #define HAL_SAI_MODULE_ENABLED */ |
|||
#define HAL_SD_MODULE_ENABLED |
|||
#define HAL_SPI_MODULE_ENABLED |
|||
#define HAL_TIM_MODULE_ENABLED |
|||
#define HAL_UART_MODULE_ENABLED |
|||
#define HAL_USART_MODULE_ENABLED |
|||
#define HAL_IRDA_MODULE_ENABLED |
|||
#define HAL_SMARTCARD_MODULE_ENABLED |
|||
#define HAL_WWDG_MODULE_ENABLED |
|||
#define HAL_CORTEX_MODULE_ENABLED |
|||
#define HAL_PCD_MODULE_ENABLED |
|||
#define HAL_HCD_MODULE_ENABLED |
|||
|
|||
|
|||
/* ########################## HSE/HSI Values adaptation ##################### */ |
|||
/**
|
|||
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application. |
|||
* This value is used by the RCC HAL module to compute the system frequency |
|||
* (when HSE is used as system clock source, directly or through the PLL). |
|||
*/ |
|||
#if !defined (HSE_VALUE) |
|||
#define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ |
|||
#endif /* HSE_VALUE */ |
|||
|
|||
#if !defined (HSE_STARTUP_TIMEOUT) |
|||
#define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ |
|||
#endif /* HSE_STARTUP_TIMEOUT */ |
|||
|
|||
/**
|
|||
* @brief Internal High Speed oscillator (HSI) value. |
|||
* This value is used by the RCC HAL module to compute the system frequency |
|||
* (when HSI is used as system clock source, directly or through the PLL). |
|||
*/ |
|||
#if !defined (HSI_VALUE) |
|||
#define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ |
|||
#endif /* HSI_VALUE */ |
|||
|
|||
/**
|
|||
* @brief External clock source for I2S peripheral |
|||
* This value is used by the I2S HAL module to compute the I2S clock source |
|||
* frequency, this source is inserted directly through I2S_CKIN pad. |
|||
*/ |
|||
#if !defined (EXTERNAL_CLOCK_VALUE) |
|||
#define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/ |
|||
#endif /* EXTERNAL_CLOCK_VALUE */ |
|||
|
|||
/* Tip: To avoid modifying this file each time you need to use different HSE,
|
|||
=== you can define the HSE value in your toolchain compiler preprocessor. */ |
|||
|
|||
/* ########################### System Configuration ######################### */ |
|||
/**
|
|||
* @brief This is the HAL system configuration section |
|||
*/ |
|||
#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ |
|||
#define USE_RTOS 0 |
|||
#define PREFETCH_ENABLE 1 |
|||
#define INSTRUCTION_CACHE_ENABLE 1 |
|||
#define DATA_CACHE_ENABLE 1 |
|||
|
|||
/* ########################## Assert Selection ############################## */ |
|||
/**
|
|||
* @brief Uncomment the line below to expanse the "assert_param" macro in the |
|||
* HAL drivers code |
|||
*/ |
|||
/* #define USE_FULL_ASSERT 1 */ |
|||
|
|||
/* ################## Ethernet peripheral configuration ##################### */ |
|||
|
|||
/* Section 1 : Ethernet peripheral configuration */ |
|||
|
|||
/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ |
|||
#define MAC_ADDR0 2 |
|||
#define MAC_ADDR1 0 |
|||
#define MAC_ADDR2 0 |
|||
#define MAC_ADDR3 0 |
|||
#define MAC_ADDR4 0 |
|||
#define MAC_ADDR5 0 |
|||
|
|||
/* Definition of the Ethernet driver buffers size and count */ |
|||
#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ |
|||
#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ |
|||
#define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ |
|||
#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ |
|||
|
|||
/* Section 2: PHY configuration section */ |
|||
|
|||
/* DP83848 PHY Address*/ |
|||
#define DP83848_PHY_ADDRESS 0x01 |
|||
/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ |
|||
#define PHY_RESET_DELAY ((uint32_t)0x000000FF) |
|||
/* PHY Configuration delay */ |
|||
#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) |
|||
|
|||
#define PHY_READ_TO ((uint32_t)0x0000FFFF) |
|||
#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) |
|||
|
|||
/* Section 3: Common PHY Registers */ |
|||
|
|||
#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ |
|||
#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ |
|||
|
|||
#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ |
|||
#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ |
|||
#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ |
|||
#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ |
|||
#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ |
|||
#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ |
|||
#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ |
|||
#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ |
|||
#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ |
|||
#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ |
|||
|
|||
#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ |
|||
#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ |
|||
#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ |
|||
|
|||
/* Section 4: Extended PHY Registers */ |
|||
|
|||
#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */ |
|||
#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */ |
|||
#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */ |
|||
|
|||
#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ |
|||
#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ |
|||
#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ |
|||
|
|||
#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ |
|||
#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ |
|||
|
|||
#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ |
|||
#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ |
|||
|
|||
/* Includes ------------------------------------------------------------------*/ |
|||
/**
|
|||
* @brief Include module's header file |
|||
*/ |
|||
|
|||
#ifdef HAL_RCC_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_rcc.h" |
|||
#endif /* HAL_RCC_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_GPIO_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_gpio.h" |
|||
#endif /* HAL_GPIO_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_DMA_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_dma.h" |
|||
#endif /* HAL_DMA_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_CORTEX_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_cortex.h" |
|||
#endif /* HAL_CORTEX_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_ADC_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_adc.h" |
|||
#endif /* HAL_ADC_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_CAN_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_can.h" |
|||
#endif /* HAL_CAN_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_CRC_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_crc.h" |
|||
#endif /* HAL_CRC_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_CRYP_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_cryp.h" |
|||
#endif /* HAL_CRYP_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_DMA2D_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_dma2d.h" |
|||
#endif /* HAL_DMA2D_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_DAC_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_dac.h" |
|||
#endif /* HAL_DAC_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_DCMI_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_dcmi.h" |
|||
#endif /* HAL_DCMI_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_ETH_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_eth.h" |
|||
#endif /* HAL_ETH_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_FLASH_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_flash.h" |
|||
#endif /* HAL_FLASH_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_SRAM_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_sram.h" |
|||
#endif /* HAL_SRAM_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_NOR_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_nor.h" |
|||
#endif /* HAL_NOR_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_NAND_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_nand.h" |
|||
#endif /* HAL_NAND_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_PCCARD_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_pccard.h" |
|||
#endif /* HAL_PCCARD_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_SDRAM_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_sdram.h" |
|||
#endif /* HAL_SDRAM_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_HASH_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_hash.h" |
|||
#endif /* HAL_HASH_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_I2C_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_i2c.h" |
|||
#endif /* HAL_I2C_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_I2S_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_i2s.h" |
|||
#endif /* HAL_I2S_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_IWDG_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_iwdg.h" |
|||
#endif /* HAL_IWDG_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_LTDC_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_ltdc.h" |
|||
#endif /* HAL_LTDC_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_PWR_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_pwr.h" |
|||
#endif /* HAL_PWR_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_RNG_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_rng.h" |
|||
#endif /* HAL_RNG_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_RTC_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_rtc.h" |
|||
#endif /* HAL_RTC_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_SAI_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_sai.h" |
|||
#endif /* HAL_SAI_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_SD_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_sd.h" |
|||
#endif /* HAL_SD_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_SPI_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_spi.h" |
|||
#endif /* HAL_SPI_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_TIM_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_tim.h" |
|||
#endif /* HAL_TIM_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_UART_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_uart.h" |
|||
#endif /* HAL_UART_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_USART_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_usart.h" |
|||
#endif /* HAL_USART_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_IRDA_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_irda.h" |
|||
#endif /* HAL_IRDA_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_SMARTCARD_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_smartcard.h" |
|||
#endif /* HAL_SMARTCARD_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_WWDG_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_wwdg.h" |
|||
#endif /* HAL_WWDG_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_PCD_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_pcd.h" |
|||
#endif /* HAL_PCD_MODULE_ENABLED */ |
|||
|
|||
#ifdef HAL_HCD_MODULE_ENABLED |
|||
#include "stm32f4xx_hal_hcd.h" |
|||
#endif /* HAL_HCD_MODULE_ENABLED */ |
|||
|
|||
/* Exported macro ------------------------------------------------------------*/ |
|||
#ifdef USE_FULL_ASSERT |
|||
/**
|
|||
* @brief The assert_param macro is used for function's parameters check. |
|||
* @param expr: If expr is false, it calls assert_failed function |
|||
* which reports the name of the source file and the source |
|||
* line number of the call that failed. |
|||
* If expr is true, it returns no value. |
|||
* @retval None |
|||
*/ |
|||
#define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) |
|||
/* Exported functions ------------------------------------------------------- */ |
|||
void assert_failed(uint8_t* file, uint32_t line); |
|||
#else |
|||
#define assert_param(expr) ((void)0) |
|||
#endif /* USE_FULL_ASSERT */ |
|||
|
|||
|
|||
|
|||
#ifdef __cplusplus |
|||
} |
|||
#endif |
|||
|
|||
#endif /* __STM32F4xx_HAL_CONF_H */ |
|||
|
|||
|
|||
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
|||
Loading…
Reference in new issue