From 769e37b64619cf1dcf8a865d39b1341afaddbd2a Mon Sep 17 00:00:00 2001 From: Tobias Badertscher Date: Fri, 18 May 2018 09:05:32 +0200 Subject: [PATCH] stm32/boards: Add config files for new board, STM32L496GDISC. --- .../boards/STM32L496GDISC/mpconfigboard.h | 52 +++ .../boards/STM32L496GDISC/mpconfigboard.mk | 7 + ports/stm32/boards/STM32L496GDISC/pins.csv | 140 ++++++ .../STM32L496GDISC/stm32l4xx_hal_conf.h | 421 ++++++++++++++++++ 4 files changed, 620 insertions(+) create mode 100644 ports/stm32/boards/STM32L496GDISC/mpconfigboard.h create mode 100644 ports/stm32/boards/STM32L496GDISC/mpconfigboard.mk create mode 100644 ports/stm32/boards/STM32L496GDISC/pins.csv create mode 100644 ports/stm32/boards/STM32L496GDISC/stm32l4xx_hal_conf.h diff --git a/ports/stm32/boards/STM32L496GDISC/mpconfigboard.h b/ports/stm32/boards/STM32L496GDISC/mpconfigboard.h new file mode 100644 index 0000000000..6a17d74d3a --- /dev/null +++ b/ports/stm32/boards/STM32L496GDISC/mpconfigboard.h @@ -0,0 +1,52 @@ +#define MICROPY_HW_BOARD_NAME "L496G-DISCO" +#define MICROPY_HW_MCU_NAME "STM32L496" + +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_TIMER (1) +#define MICROPY_HW_ENABLE_USB (1) + +// MSI is used and is 4MHz, +// Resulting core frequency is 80MHz: +#define MICROPY_HW_CLK_PLLM (1) +#define MICROPY_HW_CLK_PLLN (40) +#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7) +#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2) +#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2) + +#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4 + +// USART config +#define MICROPY_HW_UART2_TX (pin_A2) +#define MICROPY_HW_UART2_RX (pin_D6) +// USART 2 is connected to the virtual com port on the ST-LINK +#define MICROPY_HW_UART_REPL PYB_UART_2 +#define MICROPY_HW_UART_REPL_BAUD 115200 + +// I2C busses +#define MICROPY_HW_I2C1_SCL (pin_G14) +#define MICROPY_HW_I2C1_SDA (pin_G13) +#define MICROPY_HW_I2C2_SCL (pin_H4) +#define MICROPY_HW_I2C2_SDA (pin_B14) + +// SPI busses +// -> To the arduino connector +#define MICROPY_HW_SPI1_NSS (pin_A15) +#define MICROPY_HW_SPI1_SCK (pin_A5) +#define MICROPY_HW_SPI1_MISO (pin_B4) +#define MICROPY_HW_SPI1_MOSI (pin_B5) + +// Use Sel from joystick. Joystick is pulled low. Pressing the button makes the input go high. +#define MICROPY_HW_USRSW_PIN (pin_C13) +#define MICROPY_HW_USRSW_PULL (GPIO_PULLDOWN) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) +#define MICROPY_HW_USRSW_PRESSED (1) + +// LED (The orange LED is controlled over MFX) +#define MICROPY_HW_LED1 (pin_B13) // Green +#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin)) +#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin)) +// USB config +#define MICROPY_HW_USB_FS (1) +#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10) diff --git a/ports/stm32/boards/STM32L496GDISC/mpconfigboard.mk b/ports/stm32/boards/STM32L496GDISC/mpconfigboard.mk new file mode 100644 index 0000000000..3a61746556 --- /dev/null +++ b/ports/stm32/boards/STM32L496GDISC/mpconfigboard.mk @@ -0,0 +1,7 @@ +MCU_SERIES = l4 +CMSIS_MCU = STM32L496xx +AF_FILE = boards/stm32l496_af.csv +LD_FILES = boards/stm32l496xg.ld boards/common_ifs.ld +TEXT0_ADDR = 0x08000000 +TEXT1_ADDR = 0x08004000 +OPENOCD_CONFIG = boards/openocd_stm32l4.cfg diff --git a/ports/stm32/boards/STM32L496GDISC/pins.csv b/ports/stm32/boards/STM32L496GDISC/pins.csv new file mode 100644 index 0000000000..2ee054032b --- /dev/null +++ b/ports/stm32/boards/STM32L496GDISC/pins.csv @@ -0,0 +1,140 @@ +PA0,PA0 +PA1,PA1 +PA2,PA2 +PA3,PA3 +PA4,PA4 +PA5,PA5 +PA6,PA6 +PA7,PA7 +PA8,PA8 +PA9,PA9 +PA10,PA10 +PA11,PA11 +PA12,PA12 +PA13,PA13 +PA14,PA14 +PA15,PA15 +PB0,PB0 +PB1,PB1 +PB2,PB2 +PB3,PB3 +PB4,PB4 +PB5,PB5 +PB6,PB6 +PB7,PB7 +PB8,PB8 +PB9,PB9 +PB10,PB10 +PB11,PB11 +PB12,PB12 +PB13,PB13 +PB14,PB14 +PB15,PB15 +PC0,PC0 +PC1,PC1 +PC2,PC2 +PC3,PC3 +PC4,PC4 +PC5,PC5 +PC6,PC6 +PC7,PC7 +PC8,PC8 +PC9,PC9 +PC10,PC10 +PC11,PC11 +PC12,PC12 +PC13,PC13 +PC14,PC14 +PC15,PC15 +PD0,PD0 +PD1,PD1 +PD2,PD2 +PD3,PD3 +PD4,PD4 +PD5,PD5 +PD6,PD6 +PD7,PD7 +PD8,PD8 +PD9,PD9 +PD10,PD10 +PD11,PD11 +PD12,PD12 +PD13,PD13 +PD14,PD14 +PD15,PD15 +PE0,PE0 +PE1,PE1 +PE2,PE2 +PE3,PE3 +PE4,PE4 +PE5,PE5 +PE6,PE6 +PE7,PE7 +PE8,PE8 +PE9,PE9 +PE10,PE10 +PE11,PE11 +PE12,PE12 +PE13,PE13 +PE14,PE14 +PE15,PE15 +PF0,PF0 +PF1,PF1 +PF2,PF2 +PF3,PF3 +PF4,PF4 +PF5,PF5 +PF6,PF6 +PF7,PF7 +PF8,PF8 +PF9,PF9 +PF10,PF10 +PF11,PF11 +PF12,PF12 +PF13,PF13 +PF14,PF14 +PF15,PF15 +PG0,PG0 +PG1,PG1 +PG2,PG2 +PG3,PG3 +PG4,PG4 +PG5,PG5 +PG6,PG6 +PG7,PG7 +PG8,PG8 +PG9,PG9 +PG10,PG10 +PG11,PG11 +PG12,PG12 +PG13,PG13 +PG14,PG14 +PG15,PG15 +PH0,PH0 +PH1,PH1 +PH2,PH2 +PH3,PH3 +PH4,PH4 +PH5,PH5 +PH6,PH6 +PH7,PH7 +PH8,PH8 +PH9,PH9 +PH10,PH10 +PH11,PH11 +PH12,PH12 +PH13,PH13 +PH14,PH14 +PH15,PH15 +PI0,PI0 +PI1,PI1 +PI2,PI2 +PI3,PI3 +PI4,PI4 +PI5,PI5 +PI6,PI6 +PI7,PI7 +PI8,PI8 +PI9,PI9 +PI10,PI10 +PI11,PI11 diff --git a/ports/stm32/boards/STM32L496GDISC/stm32l4xx_hal_conf.h b/ports/stm32/boards/STM32L496GDISC/stm32l4xx_hal_conf.h new file mode 100644 index 0000000000..884db5ef1a --- /dev/null +++ b/ports/stm32/boards/STM32L496GDISC/stm32l4xx_hal_conf.h @@ -0,0 +1,421 @@ +/** + ****************************************************************************** + * @file stm32l4xx_hal_conf.h + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2018 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32L4xx_HAL_CONF_H +#define __STM32L4xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ + +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +/*#define HAL_CRYP_MODULE_ENABLED */ +#define HAL_CAN_MODULE_ENABLED +/* #define HAL_COMP_MODULE_ENABLED */ +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +#define HAL_DAC_MODULE_ENABLED +/* #define HAL_DCMI_MODULE_ENABLED */ +/*#define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +/*#define HAL_DSI_MODULE_ENABLED */ +/*#define HAL_FIREWALL_MODULE_ENABLED */ +/*#define HAL_GFXMMU_MODULE_ENABLED */ +/*#define HAL_HCD_MODULE_ENABLED */ +/*#define HAL_HASH_MODULE_ENABLED */ +/*#define HAL_I2S_MODULE_ENABLED */ +/*#define HAL_IRDA_MODULE_ENABLED */ +/*#define HAL_IWDG_MODULE_ENABLED */ +/*#define HAL_LTDC_MODULE_ENABLED */ +/*#define HAL_LCD_MODULE_ENABLED */ +/*#define HAL_LPTIM_MODULE_ENABLED */ +/*#define HAL_NAND_MODULE_ENABLED */ +/*#define HAL_NOR_MODULE_ENABLED */ +/*#define HAL_OPAMP_MODULE_ENABLED */ +/*#define HAL_OSPI_MODULE_ENABLED */ +#define HAL_PCD_MODULE_ENABLED +#define HAL_RNG_MODULE_ENABLED +#define HAL_RTC_MODULE_ENABLED +/* #define HAL_SAI_MODULE_ENABLED */ +#define HAL_SD_MODULE_ENABLED +/* #define HAL_SMBUS_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +#define HAL_SPI_MODULE_ENABLED +/*#define HAL_SRAM_MODULE_ENABLED */ +/*#define HAL_SWPMI_MODULE_ENABLED */ +#define HAL_TIM_MODULE_ENABLED +/*#define HAL_TSC_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/*#define HAL_USART_MODULE_ENABLED */ +/*#define HAL_WWDG_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +#define HAL_I2C_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_CORTEX_MODULE_ENABLED + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal Multiple Speed oscillator (MSI) default value. + * This value is the default MSI range value after Reset. + */ +#if !defined (MSI_VALUE) + #define MSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* MSI_VALUE */ +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + + /** + * @brief Internal High Speed oscillator (HSI48) value for USB FS, SDMMC and RNG. + * This internal oscillator is mainly dedicated to provide a high precision clock to + * the USB peripheral by means of a special Clock Recovery System (CRS) circuitry. + * When the CRS is not used, the HSI48 RC oscillator runs on it default frequency + * which is subject to manufacturing process variations. + */ + #if !defined (HSI48_VALUE) + #define HSI48_VALUE ((uint32_t)48000000U) /*!< Value of the Internal High Speed oscillator for USB FS/SDMMC/RNG in Hz. + The real value my vary depending on manufacturing process variations.*/ + #endif /* HSI48_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for SAI1 peripheral + * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source + * frequency. + */ +#if !defined (EXTERNAL_SAI1_CLOCK_VALUE) + #define EXTERNAL_SAI1_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI1 External clock source in Hz*/ +#endif /* EXTERNAL_SAI1_CLOCK_VALUE */ + +/** + * @brief External clock source for SAI2 peripheral + * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source + * frequency. + */ +#if !defined (EXTERNAL_SAI2_CLOCK_VALUE) + #define EXTERNAL_SAI2_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI2 External clock source in Hz*/ +#endif /* EXTERNAL_SAI2_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */ +#define USE_RTOS 0 +#define PREFETCH_ENABLE 1 +#define INSTRUCTION_CACHE_ENABLE 1 +#define DATA_CACHE_ENABLE 1 + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver + * Activated: CRC code is present inside driver + * Deactivated: CRC code cleaned from driver + */ + +#define USE_SPI_CRC 0 + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32l4xx_hal_rcc.h" + #include "stm32l4xx_hal_rcc_ex.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32l4xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32l4xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32l4xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32l4xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32l4xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32l4xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32l4xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32l4xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32l4xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32l4xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32l4xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32l4xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32l4xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_FIREWALL_MODULE_ENABLED + #include "stm32l4xx_hal_firewall.h" +#endif /* HAL_FIREWALL_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32l4xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32l4xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32l4xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32l4xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32l4xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32l4xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32l4xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LCD_MODULE_ENABLED + #include "stm32l4xx_hal_lcd.h" +#endif /* HAL_LCD_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED + #include "stm32l4xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED + #include "stm32l4xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_OPAMP_MODULE_ENABLED + #include "stm32l4xx_hal_opamp.h" +#endif /* HAL_OPAMP_MODULE_ENABLED */ + +#ifdef HAL_OSPI_MODULE_ENABLED + #include "stm32l4xx_hal_ospi.h" +#endif /* HAL_OSPI_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32l4xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32l4xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32l4xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32l4xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32l4xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32l4xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32l4xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32l4xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_SWPMI_MODULE_ENABLED + #include "stm32l4xx_hal_swpmi.h" +#endif /* HAL_SWPMI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32l4xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_TSC_MODULE_ENABLED + #include "stm32l4xx_hal_tsc.h" +#endif /* HAL_TSC_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32l4xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32l4xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32l4xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32l4xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32l4xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32l4xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32l4xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_GFXMMU_MODULE_ENABLED + #include "stm32l4xx_hal_gfxmmu.h" +#endif /* HAL_GFXMMU_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32L4xx_HAL_CONF_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/