pyb.delay and pyb.udelay now use systick if IRQs are enabled, otherwise
they use a busy loop. Thus they work correctly when IRQs are disabled.
The busy loop is computed from the current CPU frequency, so works no
matter the CPU frequency.
Also restrict higher frequencies to have a VCO_OUT frequency below
432MHz, as specified in the datasheet.
Docs improved to list allowed frequencies, and explain about USB
stability.
Found these by compiling stmhal with mp_uint_t of type uint32_t instead
of unsigned int. This actually makes a difference to the code, but just
a curiosity.
Eg pyb.freq(120000000) sets the CPU to 120MHz. The frequency can be set
at any point in the code, and can be changed as many times as you like.
Note that any active timers will need to be reconfigured after a freq
change.
Valid range is 24MHz to 168MHz (but not all freqs are supported). The
code maintains a 48MHz clock for the USB at all times and it's possible
to change the frequency at a USB REPL and keep the REPL alive (well,
most of the time it stays, sometimes it resets the USB for some reason).
Note that USB does not work with pyb.freq of 24MHz.
I also removed trailing spaces from modpyb.c which affected a couple
of lines technically not part of this patch.
Tested using: https://github.com/dhylands/upy-examples/blob/master/micros_test.py
which eventually fails due to wraparound issues (I could fix the test to compensate
but didn't bother)
It's still "safe" because no scripts are run. Remove the SD card if you
want to access the internal flash filesystem. Addresses issue #616.
Also: remove obsolete pyb.source_dir setting, and reset pyb.main and
pyb.usb_mode settings on soft-reset.
Some important changes to the way the file system is structured on the
pyboard:
1. 0: and 1: drive names are now replaced with POSIX inspired
directories, namely /flash and /sd.
2. Filesystem now supports the notion of a current working directory.
Supports the standard Python way of manipulating it: os.chdir and
os.getcwd.
3. On boot up, current directory is /flash if no SD inserted, else /sd
if SD inserted. Then runs boot.py and main.py from the current dir.
This is the same as the old behaviour, but is much more consistent and
flexible (eg you can os.chdir in boot.py to change where main.py is run
from).
4. sys.path (for import) is now set to '' (current dir), plus /flash
and /flash/lib, and then /sd and /sd/lib if SD inserted. This, along
with CWD, means that import now works properly. You can import a file
from the current directory.
5. os.listdir is fixed to return just the basename, not the full path.
See issue #537 for background and discussion.
Before, pyb.stdin/pyb.stdout allowed some kind of access to the USB VCP
device, but it was basic access.
This patch adds a proper USB_VCP class and object with much more control
over the USB VCP device. Create an object with pyb.USB_VCP(), then use
this object as if it were a UART object. It has send, recv, read,
write, and other methods. send and recv allow a timeout to be specified.
Addresses issue 774.
Recent changes to builtin print meant that print was printing to the
mp_sys_stdout_obj, which was sending data raw to the USB CDC device.
The data should be cooked so that \n turns into \r\n.
This adds a hook to get/set pyb_uart_global_debug from Python, using
pyb.repl_uart(). You can set it to an arbitrary UART object, and then
the REPL (in and out) is repeated on this UART object (as well as on USB
CDC).
Ultimately, this will be replaced with a proper Pythonic interface to
set sys.stdin and sys.stdout.
Blanket wide to all .c and .h files. Some files originating from ST are
difficult to deal with (license wise) so it was left out of those.
Also merged modpyb.h, modos.h, modstm.h and modtime.h in stmhal/.
Decided to write own script to pull documentation from comments in C code.
Style for writing auto generated documentation is: start line with ///
and then use standard markdown to write the comment. Keywords
recognised by the scraper begin with backslash. See code for examples.
Running: python gendoc.py modpyb.c accel.c adc.c dac.c extint.c i2c.c
led.c pin.c rng.c servo.c spi.c uart.c usrsw.c, will generate a HTML
structure in gendoc-out/.
gendoc.py is crude but functional. Needed something quick, and this was
it.
Instead of pyb.switch() as a function, it's more consistent (with
respect to all the other modules and peripherals) to have
pyb.Switch() create a switch object. This then generalises to having
multiple switches. Call the object to get its state. Use sw.callback
to set the callback function for when the switch is pressed.
Simple but functional timer control. More sophistication will
eventually be added, or for now just use direct register access :)
Also added pyb.freq() function to get MCU clock frequencies.
It's really a UART because there is no external clock line (and hence no
synchronous ability, at least in the implementation of this module).
USART should be reserved for a module that has "S"ynchronous capabilities.
Also, UART is shorter and easier to type :)
This is an attempt to clean up the Micro Python API on the pyboard.
Gpio functionality is now in the Pin object, which seems more natural.
Constants for MODE and PULL are now in pyb.Pin. Names of some
classes have been adjusted to conform to CamelCase. Other
miscellaneous changes and clean up here and there.
Pretty much everyone needs to include map.h, since it's such an integral
part of the Micro Python object implementation. Thus, the definitions
are now in obj.h instead. map.h is removed.
Damien George
Dave Hylands
Emmanuel Blot
Sven Wegener
Paul Sokolovsky