You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
85 lines
3.0 KiB
85 lines
3.0 KiB
Branch instructions
|
|
===================
|
|
|
|
These cause execution to jump to a target location usually specified by a label (see the ``label``
|
|
assembler directive). Conditional branches and the ``it`` and ``ite`` instructions test
|
|
the Application Program Status Register (APSR) N (negative), Z (zero), C (carry) and V
|
|
(overflow) flags to determine whether the branch should be executed.
|
|
|
|
Most of the exposed assembler instructions (including move operations) set the flags but
|
|
there are explicit comparison instructions to enable values to be tested.
|
|
|
|
Further detail on the meaning of the condition flags is provided in the section
|
|
describing comparison functions.
|
|
|
|
Document conventions
|
|
--------------------
|
|
|
|
Notation: ``Rm`` denotes ARM registers R0-R15. ``LABEL`` denotes a label defined with the
|
|
``label()`` assembler directive. ``<condition>`` indicates one of the following condition
|
|
specifiers:
|
|
|
|
* eq Equal to (result was zero)
|
|
* ne Not equal
|
|
* cs Carry set
|
|
* cc Carry clear
|
|
* mi Minus (negative)
|
|
* pl Plus (positive)
|
|
* vs Overflow set
|
|
* vc Overflow clear
|
|
* hi > (unsigned comparison)
|
|
* ls <= (unsigned comparison)
|
|
* ge >= (signed comparison)
|
|
* lt < (signed comparison)
|
|
* gt > (signed comparison)
|
|
* le <= (signed comparison)
|
|
|
|
Branch to label
|
|
---------------
|
|
|
|
* b(LABEL) Unconditional branch
|
|
* beq(LABEL) branch if equal
|
|
* bne(LABEL) branch if not equal
|
|
* bge(LABEL) branch if greater than or equal
|
|
* bgt(LABEL) branch if greater than
|
|
* blt(LABEL) branch if less than (<) (signed)
|
|
* ble(LABEL) branch if less than or equal to (<=) (signed)
|
|
* bcs(LABEL) branch if carry flag is set
|
|
* bcc(LABEL) branch if carry flag is clear
|
|
* bmi(LABEL) branch if negative
|
|
* bpl(LABEL) branch if positive
|
|
* bvs(LABEL) branch if overflow flag set
|
|
* bvc(LABEL) branch if overflow flag is clear
|
|
* bhi(LABEL) branch if higher (unsigned)
|
|
* bls(LABEL) branch if lower or equal (unsigned)
|
|
|
|
Long branches
|
|
-------------
|
|
|
|
The code produced by the branch instructions listed above uses a fixed bit width to specify the
|
|
branch destination, which is PC relative. Consequently in long programs where the
|
|
branch instruction is remote from its destination the assembler will produce a "branch not in
|
|
range" error. This can be overcome with the "wide" variants such as
|
|
|
|
* beq\_w(LABEL) long branch if equal
|
|
|
|
Wide branches use 4 bytes to encode the instruction (compared with 2 bytes for standard branch instructions).
|
|
|
|
Subroutines (functions)
|
|
-----------------------
|
|
|
|
When entering a subroutine the processor stores the return address in register r14, also
|
|
known as the link register (lr). Return to the instruction after the subroutine call is
|
|
performed by updating the program counter (r15 or pc) from the link register, This
|
|
process is handled by the following instructions.
|
|
|
|
* bl(LABEL)
|
|
|
|
Transfer execution to the instruction after ``LABEL`` storing the return address in
|
|
the link register (r14).
|
|
|
|
* bx(Rm) Branch to address specified by Rm.
|
|
|
|
Typically ``bx(lr)`` is issued to return from a subroutine. For nested subroutines the
|
|
link register of outer scopes must be saved (usually on the stack) before performing
|
|
inner subroutine calls.
|
|
|