You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
55 lines
1.8 KiB
55 lines
1.8 KiB
#define MICROPY_HW_BOARD_NAME "LIMIFROG"
|
|
#define MICROPY_HW_MCU_NAME "STM32L476"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
|
|
#define MICROPY_BOARD_EARLY_INIT LIMIFROG_board_early_init
|
|
void LIMIFROG_board_early_init(void);
|
|
|
|
// MSI is used and is 4MHz
|
|
#define MICROPY_HW_CLK_PLLM (1)
|
|
#define MICROPY_HW_CLK_PLLN (40)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7)
|
|
#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2)
|
|
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
|
|
|
|
// USART config
|
|
#define MICROPY_HW_UART3_TX (pin_C10)
|
|
#define MICROPY_HW_UART3_RX (pin_C11)
|
|
|
|
// I2C busses
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9)
|
|
#define MICROPY_HW_I2C2_SCL (pin_B10)
|
|
#define MICROPY_HW_I2C2_SDA (pin_B11)
|
|
|
|
// SPI busses
|
|
#define MICROPY_HW_SPI1_NSS (pin_A4)
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5)
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6)
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
|
|
|
#define MICROPY_HW_SPI3_NSS (pin_A15)
|
|
#define MICROPY_HW_SPI3_SCK (pin_B3)
|
|
#define MICROPY_HW_SPI3_MISO (pin_B4)
|
|
#define MICROPY_HW_SPI3_MOSI (pin_B5)
|
|
|
|
#define MICROPY_HW_USRSW_PIN (pin_A15)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_C3) // red
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_FS (1)
|
|
// #define MICROPY_HW_USB_OTG_ID_PIN (pin_C12) // This is not the official ID Pin which should be PA10
|
|
|