You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
71 lines
3.1 KiB
71 lines
3.1 KiB
// We use the ST Cube HAL library for most hardware peripherals
|
|
#include STM32_HAL_H
|
|
#include "pin.h"
|
|
|
|
// The unique id address differs per MCU. Ideally this define should
|
|
// go in some MCU-specific header, but for now it lives here.
|
|
#if defined(MCU_SERIES_F4)
|
|
#define MP_HAL_UNIQUE_ID_ADDRESS (0x1fff7a10)
|
|
#define MP_HAL_CLEANINVALIDATE_DCACHE(addr, size)
|
|
#define MP_HAL_CLEAN_DCACHE(addr, size)
|
|
#elif defined(MCU_SERIES_F7)
|
|
#define MP_HAL_UNIQUE_ID_ADDRESS (0x1ff0f420)
|
|
#define MP_HAL_CLEANINVALIDATE_DCACHE(addr, size) (SCB_CleanInvalidateDCache_by_Addr((uint32_t*)((uint32_t)addr & ~0x1f), ((uint32_t)(addr + size + 0x1f) & ~0x1f) - ((uint32_t)addr & ~0x1f)))
|
|
#define MP_HAL_CLEAN_DCACHE(addr, size) (SCB_CleanDCache_by_Addr((uint32_t*)((uint32_t)addr & ~0x1f), ((uint32_t)(addr + size + 0x1f) & ~0x1f) - ((uint32_t)addr & ~0x1f)))
|
|
#elif defined(MCU_SERIES_L4)
|
|
#define MP_HAL_UNIQUE_ID_ADDRESS (0x1fff7590)
|
|
#define MP_HAL_CLEANINVALIDATE_DCACHE(addr, size)
|
|
#define MP_HAL_CLEAN_DCACHE(addr, size)
|
|
#else
|
|
#error mphalport.h: Unrecognized MCU_SERIES
|
|
#endif
|
|
|
|
extern const unsigned char mp_hal_status_to_errno_table[4];
|
|
|
|
NORETURN void mp_hal_raise(HAL_StatusTypeDef status);
|
|
void mp_hal_set_interrupt_char(int c); // -1 to disable
|
|
|
|
// timing functions
|
|
|
|
#define mp_hal_delay_us_fast(us) mp_hal_delay_us(us)
|
|
|
|
extern bool mp_hal_ticks_cpu_enabled;
|
|
void mp_hal_ticks_cpu_enable(void);
|
|
static inline mp_uint_t mp_hal_ticks_cpu(void) {
|
|
if (!mp_hal_ticks_cpu_enabled) {
|
|
mp_hal_ticks_cpu_enable();
|
|
}
|
|
return DWT->CYCCNT;
|
|
}
|
|
|
|
// C-level pin HAL
|
|
|
|
#include "stmhal/pin.h"
|
|
|
|
#define MP_HAL_PIN_FMT "%q"
|
|
#define MP_HAL_PIN_MODE_INPUT (0)
|
|
#define MP_HAL_PIN_MODE_OUTPUT (1)
|
|
#define MP_HAL_PIN_MODE_ALT (2)
|
|
#define MP_HAL_PIN_MODE_ANALOG (3)
|
|
#define MP_HAL_PIN_MODE_OPEN_DRAIN (5)
|
|
#define MP_HAL_PIN_MODE_ALT_OPEN_DRAIN (6)
|
|
#define MP_HAL_PIN_PULL_NONE (GPIO_NOPULL)
|
|
#define MP_HAL_PIN_PULL_UP (GPIO_PULLUP)
|
|
#define MP_HAL_PIN_PULL_DOWN (GPIO_PULLDOWN)
|
|
|
|
#define mp_hal_pin_obj_t const pin_obj_t*
|
|
#define mp_hal_get_pin_obj(o) pin_find(o)
|
|
#define mp_hal_pin_name(p) ((p)->name)
|
|
#define mp_hal_pin_input(p) mp_hal_pin_config((p), MP_HAL_PIN_MODE_INPUT, MP_HAL_PIN_PULL_NONE, 0)
|
|
#define mp_hal_pin_output(p) mp_hal_pin_config((p), MP_HAL_PIN_MODE_OUTPUT, MP_HAL_PIN_PULL_NONE, 0)
|
|
#define mp_hal_pin_open_drain(p) mp_hal_pin_config((p), MP_HAL_PIN_MODE_OPEN_DRAIN, MP_HAL_PIN_PULL_NONE, 0)
|
|
#define mp_hal_pin_high(p) (((p)->gpio->BSRR) = (p)->pin_mask)
|
|
#define mp_hal_pin_low(p) (((p)->gpio->BSRR) = ((p)->pin_mask << 16))
|
|
#define mp_hal_pin_od_low(p) mp_hal_pin_low(p)
|
|
#define mp_hal_pin_od_high(p) mp_hal_pin_high(p)
|
|
#define mp_hal_pin_read(p) (((p)->gpio->IDR >> (p)->pin) & 1)
|
|
#define mp_hal_pin_write(p, v) do { if (v) { mp_hal_pin_high(p); } else { mp_hal_pin_low(p); } } while (0)
|
|
|
|
void mp_hal_gpio_clock_enable(GPIO_TypeDef *gpio);
|
|
void mp_hal_pin_config(mp_hal_pin_obj_t pin, uint32_t mode, uint32_t pull, uint32_t alt);
|
|
bool mp_hal_pin_config_alt(mp_hal_pin_obj_t pin, uint32_t mode, uint32_t pull, uint8_t fn, uint8_t unit);
|
|
|