You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

95 lines
2.6 KiB

Getting Started with SerialICE-1A
Getting Started with SerialICE-1A
What You'll Need
» A Host computer system (UNIX or MSDOS)
» An SerialICE Controller board
» A Target board
To run an application program on your Target using SerialICE-1A, perform the
following steps:
» If you haven't done so already,
Download
the PMON source from the Web site.
» Next you need to Extract the files
from the archive.
--
SerialICE Controller
TargetBDMR4101-beBDMR4101-le
BDMR4101-beall-beall-be-le
BDMR4011-beall-beall-be-le
BDMR4102-beall-beall-be-le
BDMR4101-leall-be-leall-le
BDMR4011-leall-be-leall-le
BDMR4102-leall-be-leall-le
BDMR4001-beall-beall-be-le
BDMR4003-beall-beall-be-le
BDMR4001-leall-be-leall-le
BDMR4003-leall-be-leall-le
L64008all-be
sdp1000all-le
sdp1000
L64363 (ATMizer2)all-be
l64363all-le
l64363
--
Key: The "-be" means Big Endian, the "-le" means Little Endian.
and sdp1000, you will need to unpack two separate copies
of the PMON sources, each in it's own directory.
--
» To configure the package you need to run the Install program using the information that you
obtained from the body of the table above.
For example, if your
selection shows "all-be", then you need to specify target type 1
during the installation (All Big Endian Processors), if "all-le" then
select target type 2 (All Little Endian Processors), if it shows
"all-be-le" then select target type 1 (All Big Endian Processors), but
when the install program presents you with a summary of all the
selected options, select the "Endian Support" option and enter "1 2"
to select both byte orderings. Do not change the "Default Endian".
The target type information is summarized below.
Target TypeTarget Name
all-be"All Processors Big Endian"
all-le"All Processors Little Endian"
all-be-le"All Processors Big Endian" and
Change "Endian Support" to "1 2"
all-le-be"All Processors Little Endian" and
Change "Endian Support" to "1 2"
nitro"4011 Nitro II"
sdp1000"SDP1000 (L64008 MPEG-2 Transport)"
l64363"ATMizer-2 R-T SAR Engine"
--
» To prepare the package for use you must
Build the package.
» Configure your hardware.
SerialICE requires an RS232 link between your host and port A on the
SerialICE Controller, and a null-modem RS232 link between port B on the
SerialICE Controller and port A on your Target. The
actual hardware port names
will depend on which host, SerialICE Controller, and Target you will be
using.
» Install the driver.
» Build,
Download and Execute your application on the Target.
««««««««««««««««««««««««««««««««««««««««»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»»
Navigation:
Document Home |
Document Contents |
Document Index