To make it easier on everyone to keep a uniform coding style throughout
the project we will be using this target to verify our code for
complience.
Currently a lot of files in the project don't fully follow the coding
style. We need to reach that spot over time though. :)
According to the reference manual, you are _forbidden_ from writing 00 to the
VOS[1:0] bits in PWR_CR. Writing a 00 is automatically turned into range 2,
or, 10. Attempting to then |= the bits for range 1 (01) results in the final
result of choosing voltage range 3 (11). This has fairly catastrophic effects
if you then attempt to switch to PLL clock at 32Mhz.
Oddly, the existing code was working fine on STM32L151C6 revision W, but
failing with revision V silicon. Regardless, the existing code was wrong and
not following the reference manual.
Further, attempting to change any power voltage range settings without the RCC
enabled will have no effect, so all the higher level helper routines
have added peripheral enable lines before attempting to set the range.
This switch to HSI was an attempt to run the setup code faster. However,
there's no real need for this, and it just confuses things by switching first
to one clock, and then to another. Just keep running on the existing clock
until switching to the clock actually chosen by the user's arguments.
Added hash processor register definitions and main functions. Hash
processor is supported in stm32f21, stm32f41 and stm32f43 and can be
used to calculate Md5 and Sha1.
Use fixed variables for things that can't change, instead of variables
like SRCLIBDIR that was causing a shell call for every single use.
Use less functions in general and less shell expansions.
Use builtin functions like $(realpath blah) instead of $(shell
pwd)/blah In particular, this was important for me trying to build on
windows with git-shell. This should help a lot on smaller build
machines, but doesn't make a huge difference on my own.
Remove redundant clean print messages. These also cause more needless
shell expansions.
Implement an API to specifiy the interrupt trigger for GPIO pins, and
control interrupts. This completes the GPIO API.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Everything needed to set up and control the GPIO pins is implemented,
EXCEPT setting up interrupts. This is the subject of a subsequent patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Put the Doxygen blocks in well-formatted C comments. This looks better
and is less distracting than putting them in unformatted comments.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The AHB bus allows faster control of GPIO pins versus the older APB bus.
The GPIO ports A through H default on the APB bus. Change the GPIOx
defines in gpio.h to use the base address of the AHB bus.
There's another reason to use the AHB bus: ports K tand highercan only be
accessed via the AHB bus.
***WARNING***
To work, GPIO acces to the AHB bus must be explictly enabled via the
GPIOHBCTL register. Without any additional change, this patch will break
any code using the older APB bus. If the GPIOHBCTL is not properly
modified, any acces to the GPIO register will cause a hard fault.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Modify lm4f_ep_read/write_packet() to take advantage of 32-bit and 16-bit
accesses to the USB FIFO, as opposed to using only 8-bit accesses. This
change increases endpoint performance in a number of configurations.
On the host side, we use usb_bulk_bench to test
https://github.com/mrnuke/usb_bulk_bench
With the following invocations:
usb_bulk_bench -d c03e:b007 -a -t 64 -q 32 -e [ep] [-I/-O]
On the device side, we use the usb_bulk_dev example:
https://github.com/mrnuke/libopencm3-examples/tree/stellaris
The example is in: examples/lm4f/stellaris-ek-lm4f120xl/usb_bulk_dev
(This example will be available in libopencm3-examples in the near future)
The endpoints configuration is the following:
* EP1 OUT - interrupt driven RX endpoint
* EP2 IN - interrupt driven TX endpoint
* EP3 OUT - polled RX endpoint
* EP4 IN - polled TX endpoint
* EP5 OUT - polled RX endpoint with unaligned buffer
* EP6 IN - polled TX endpoint with unaligned buffer
We test the speed in each configuration, using different system clock
frequencies. We run the tests once without the patch applied, and once with
the patch applied. The results are given below:
Before patch (numbers in KiB/s):
freq: 80 MHz 57 MHz 40 MHz 30 MHz 20 MHz 16 MHz
EP1 562 562 562 562 562 550
EP2 936 872 812 812 687 625
EP3 1062 890 700 600 562 562
EP4 900 812 812 750 625 562
EP5 1062 890 700 600 562 562
EP6 930 812 812 750 625 562
With patch (numbers in KiB/s):
freq: 80 MHz 57 MHz 40 MHz 30 MHz 20 MHz 16 MHz
EP1 1062 1062 1062 690 562 562
EP2 1125 936 936 936 870 812
EP3 1062 960 750 750 562 562
EP4 936 936 870 870 770 700
EP5 1062 900 700 630 562 562
EP6 930 930 870 870 740 650
Percent change in speed (*):
freq: 80 MHz 57 MHz 40 MHz 30 MHz 20 MHz 16 MHz
EP1 89.0 89.0 89.0 22.8 0.0 2.2
EP2 20.2 7.3 15.3 15.3 26.6 29.9
EP3 0.0 7.9 7.1 25.0 0.0 0.0
EP4 4.0 15.3 7.1 16.0 23.2 24.6
EP5 0.0 1.1 0.0 5.0 0.0 0.0
EP6 0.0 14.5 7.1 16.0 18.4 15.7
(*) Numbers given as percent change relative to speed before applying this
patch.
We see throughput increases across the board.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add functions to enable and disable USB interrupts, and document how to
use these functions to run usbd_poll() from the usb ISR.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Implement a basic driver for the LM4F USB controller. The driver is in a
basic form. DMA is not yet implemented. Double-buffering is supported by
the hardware, but is not yet implemented
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Change flash_erase_sector (f2/f4) to take numerical sector argument.
As opposed to using one of the defines in the header, this is more convenient when programatically deciding which sectors to erase.
Add a complete API for controlling the UART interrupts.
Doxygen documentation with inline code examples is also provided in this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add basic functionality needed to setup the UART and send/recieve data.
Interrupts, DMA, and more advanced features are not implemented in this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
By somo copypaste error, the doxygen group rcc_defines was defined twice.
Don't do that. Keep Ken's doxygen structure and drop the old one.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Piotr Esden-Tempski
Felix Ruess
Karl Palsson
Ben Gamari
Mikhail Avkhimenia
Ken Sarkies
Paul Fleischer
Gareth McMullin
Alexandru Gagniuc
Fergus Noble
Michael Aherne
Gareth McMullin